MED415222CS!001ENG- -  -  N- WallMax Multiple Cable Penetration Transits - WRHFFL series -N- S- S- -18/10/2022- Marine Equipment- - SN- S- - N-  - 396,753B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità- MED415222CS/001- N-Oct 17, 2027396753
 
Form
  Marine Equipment(TO)
Certification N. MED415222CS/001 - (ENG)
Certificate date 18/10/2022
Type Protezione antincendio
Product Penetrations through "A" Class divisions: (a) electric cable transits
Item Nº MED/3.26a
USCG Category N° 164.138

Model or Denomin.
Items
WallMax Multiple Cable Penetration Transits -  WRHFFL series
Applicant WALLMAX SRL
Place of requester CORSO DI PORTA NUOVA 22  %  20121 MILANO  % ITALY
Tel. N.,Fax, Email 02 2171 1156, 02 93650825, ---
Directive (EU) 2022/1157
Standards IMO Res. MSC.307(88)-(2010 FTP Code) - IMO MSC.1/Circ. 1488
Reference Documents Chap. II-2 of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Request 17/10/2022
Expire date 17/10/2027
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED415222CS/001

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2022/1157.
MED Item Nº MED/3.26a
USCG Category Nº 164.138
Description Penetrations through "A" Class divisions: (a) electric cable transits
Type WallMax Multiple Cable Penetration Transits -  WRHFFL series
Applicant WALLMAX SRL
CORSO DI PORTA NUOVA 22,20121 MILANO,ITALY
Testing standards IMO Res. MSC.307(88)-(2010 FTP Code) - IMO MSC.1/Circ. 1488
Reference standards Chap. II-2 of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Issued in Genoa on
This Certificate is valid until
October 18, 2022
October 17, 2027
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED415222CS/001
Page 1 of 3

Product description

Transits of electric cables, having maximum diameter of 81 mm, installed in A-Class decks. The transits are composed of a steel frame, having thickness of 6 and 10 mm and depth of 60 mm fitted with flange that may be bolted or welded to the deck plate. The transits are filled with EPDM modules and, on the upper part, one module fitted with a screw expander is installed. The interstices between the cables and the modules and between the modules, are lubricated by means of product named WallMax Lubricant. The transits are insulated, on both sides, with two layers of mineral wool type SeaRox SL 620, having, each, thickness of 60 mm and density of 100 kg/m3; the mineral wool panels, having dimensions of 400 mm in width and 600 mm (320 mm for frame type WRHFFL 60) in length, are fixed to the deck plate by means of steel pins and washers welded with pitch ranging from 120 up to 200 mm. The certification is valid also for transit types WRFF, WRHFF and WRFFL and for types WRFFO, WRHFFO, WRFFLO, WRHFFLO composed of a three-side frame with the fourth side welded or bolted afterwards.
Field of application
Fire resistant A-60 Class cable transits through decks as per following table:
Transit dimensions (mm)
Flange dimensions (mm)
Minimum fill
%
Maximum fill
%
Cables - Maximum diameter (mm)
132x110
252x230
0.08
33.4
50
132x290
252x410
0.03
33.5
81
Reference documents
WallMax drawing No. 5500002001 rev. 00 dated 1 August 2017 and No. 7010102004 Rev. 00 dated 23 June 2017 approved on 22 September 2017 and 16 October 2017 respectively with endorsement Nos. LABS-1537 and LABS-1556.
Tests carried out
Tests as per RINA Test Laboratory Report No. 2017CS01761/6 issued on 22 September 2017 according to Appendix 1 of IMO 2010 FTPC Part 3 - A.IV Cable Transits.




ATTACHMENT TO
CERTIFICATE No. MED415222CS/001
Pages 3 of 3
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****