MED065826CSENGB- -  -  N- 3mm Steel Bulkhead A60 -N- S- S- -20/02/2026- Marine Equipment- - SN- S- - N-  - 704,840B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED065826CS- N-Feb 19, 2031704840
 
Form
  Marine Equipment(TO)
MED065826CS
Certification N. MED065826CS - (ENG)
Certificate date 20/02/2026
Type Protezione antincendio
Product 'A' and 'B' Class divisions fire integrity: (a) 'A' Class divisions
Item Nº MED/3.11a
USCG Category N° 164.107

Model or Denomin.
Items
3mm Steel Bulkhead A60
Applicant Promat Research and Technology Centre - PROMAT RESEARCH AND TECHNOLOGY CENTRE
Place of requester BORMSTRAAT 24  %  2830 Tisselt  % BELGIUM
Tel. N.,Fax, Email +32 15 71 82 70, ---, invoices.be@etexgroup.com
Directive (EU) 2025/1533
Standards IMO Res. MSC.307(88)-(2010 FTP Code), as amended - IMO MSC.1/Circ. 1435
Reference Documents SOLAS 74 Reg. II-2/3.2, SOLAS 74 Reg. II-2/9, IMO MSC/Circ.1120, IMO MSC.1/Circ.1434, IMO MSC.1/Circ.1616,IMO Circ. MSC.1 1621
Request 23/01/2026
Expire date 19/02/2031
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED065826CS

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2025/1533.
MED Item Nº MED/3.11a
USCG Category Nº 164.107
Description 'A' and 'B' Class divisions fire integrity: (a) 'A' Class divisions
Type 3mm Steel Bulkhead A60
Applicant Promat Research and Technology Centre - PROMAT RESEARCH AND TECHNOLOGY CENTRE
BORMSTRAAT 24,2830 Tisselt,BELGIUM
Testing standards IMO Res. MSC.307(88)-(2010 FTP Code), as amended - IMO MSC.1/Circ. 1435
Reference standards SOLAS 74 Reg. II-2/3.2, SOLAS 74 Reg. II-2/9, IMO MSC/Circ.1120, IMO MSC.1/Circ.1434, IMO MSC.1/Circ.1616; IMO Circ. MSC.1 1621
Issued in Genoa on
This Certificate is valid until
February 20, 2026
February 19, 2031
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED065826CS
Page 1 of 2

Product description



Bulkhead composed of a carbon steel plate having thickness of 3 mm fitted with ā€œLā€ shaped stiffeners, having dimensions of 65x65 mm and thick 6 mm, fitted every 600 mm. The insulating material, named PROMAGUARD, is composed of panels of material having, each, dimensions of 1200x600 mm, thickness of 10 mm and density of 240 kg/m3. Such material, composed of two panel layers, on the stiffened side, is laid on the stiffeners and fixed to the bulkhead plate, by means of pins welded with pitch ranging from 400 mm up to 540mm. The panels are fitted in way that the longer side is parallel to the bulkhead stiffeners. The panel joints are obtained approaching the panels. The external panel layer is applied such as the transversal panel joints are staggered by 600 mm, with respect to the same relevant to the lower layer.

Field of application

Fire resistant A-60 Class bulkhead for general application.
The certified item is not in compliance with the requirement of Fire Test Procedure Code Part 3 regarding the plate thickness and this characteristic must be taken into account.


The surfaces of this division may be fitted with products having low flame spread characteristics, installed as described in the relevant type approval certificates and satisfying the requirements of SOLAS 74 Reg. II-2 as applicable.
Reference documents

Promat Research and Technology Centre drawing No. R05 DAM 26, Rev. 0, dated 12 February 2026, included in RINA Test Laboratory test report No. 2026CS01658 issued on 20/02/2026.

Tests carried out

Tests as per RINA Test Laboratory test report No. 2026CS01658 issued on 20/02/2026 according to IMO Res. MSC.307(88)-(2010 FTP Code) as amended, Part. 3.




ATTACHMENT TO
CERTIFICATE No. MED065826CS
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****