MED011123CS!001ENGF- -  -  N- IMO GOLD - LEATHER WEAVE -N- S- S- -23/01/2023- Marine Equipment- - SN- S- - N-  - 375,096B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità- MED011123CS/001- N-Nov 7, 2027375096
 
Form
  Marine Equipment(TO)
Certification N. MED011123CS/001 - (ENG)
Certificate date 23/01/2023
Type Protezione antincendio
Product Surface materials and floor coverings with low flame-spread characteristics: (a) decorative veneers
Item Nº MED/3.18a
USCG Category N° 164.112

Model or Denomin.
Items/Sizes
IMO GOLD - LEATHER WEAVE
Applicant FOGLIZZO LEATHER SRL
Place of requester Via Forli, 164  %  10149 Torino (TO)  % ITALY
Tel. N.,Fax, Email 011 5818728, 011 4512109, ---
Directive (EU) 2022/1157
Standard IMO Res. MSC.307(88)-(2010 FTP Code)
Reference Documents Chap. II-2 of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Request 18/01/2023
Validity date 07/11/2027
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED011123CS/001

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2022/1157.
MED Item Nº MED/3.18a
USCG Category Nº 164.112
Description Surface materials and floor coverings with low flame-spread characteristics: (a) decorative veneers
Type IMO GOLD - LEATHER WEAVE
Applicant FOGLIZZO LEATHER SRL
Via Forli, 164,10149 Torino (TO),ITALY
Testing standards IMO Res. MSC.307(88)-(2010 FTP Code)
Reference standards Chap. II-2 of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Issued in Genoa on
This Certificate is valid until
January 23, 2023
November 7, 2027
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED011123CS/001
Page 1 of 2

Product description


Braided leather.
  • Mass per area range (g/m2) 1200 ÷ 2900 ± 15%
  • Thickness range (mm) 1.7 ÷ 4 ± 15%


Field of application

As finishing material for all exposed interior and concealed or inaccessible surfaces. The product may be placed to any metallic support having thickness equal to or greater than 0.75 mm.
On the basis of the value of the total heat release (Qt) and on the basis of the value of the peak heat release (qp) the material is deemed not generating excessive quantities of smoke nor toxic products in fire according to Annex 2 IMO 2010 FTP Code.
Where applicable the requirement of Chapter II-2/34 of SOLAS 1974 relevant to the calorific potential for surface unit should not exceed the maximum value of 45 MJ/m2, the product having thickness of 4 mm may be applied on a limited surface; the use of the product on the whole surface is limited to maximum thickness of 3.3 mm.



Tests carried out

Tests as per RINA Test Laboratory reports No. 2017CS012746/2 dated 23 October 2017 and No. 2017CS012746/3 dated 7 November 2017 issued according to:
  • IMO 2010 FTP Code Part 5
  • ISO 1716: 2010




ATTACHMENT TO
CERTIFICATE No. MED011123CS/001
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****