MED388824CSENGB- -  -  N- Window 3 Parts A0 -N- S- S- -04/06/2024- Marine Equipment- - SN- S- - N-  - 342,694B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED388824CS- N-Jun 3, 2029342694
 
Form
  Marine Equipment(TO)
MED388824CS
Certification N. MED388824CS - (ENG)
Certificate date 04/06/2024
Type Protezione antincendio
Product 'A' & 'B' class fire proof windows and side scuttles
Item Nº MED/3.25

Model or Denomin.
Items
Window 3 Parts A0
Applicant HET ANKER BV
Place of requester Kaatsbaan, 10 4209 AD SCHELLUINEN  % NETHERLANDS
Tel. N.,Fax, Email +31183623135, truus@anker-windows.com, ---
Directive (EU) 2023/1667
Standards IMO Res. MSC.307(88)-(2010 FTP Code)
Reference Documents Chap. II-2 of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Request 30/05/2024
Expire date 03/06/2029
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED388824CS

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2023/1667.
MED Item Nº MED/3.25
Description 'A' & 'B' class fire proof windows and side scuttles
Type Window 3 Parts A0
Applicant HET ANKER BV
Kaatsbaan, 10 4209 AD SCHELLUINEN,NETHERLANDS
Testing standards IMO Res. MSC.307(88)-(2010 FTP Code)
Reference standards Chap. II-2 of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Issued in Genoa on
This Certificate is valid until
June 4, 2024
June 3, 2029
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED388824CS
Page 1 of 2

Product description

Window composed of three or more panes having, each, maximum clear size of 770 mm in width and 2200 mm in height. The glass compound, moving from the exposed side, is composed of a toughened glass type PYRAN S (manufacturer Schott – Germany) having thickness of 6 mm, a cavity 12 mm deep and a toughened glass having thickness of 10 mm (manufacturer Veneto Vetro). The central mullions, moving from the unexposed side, are composed of a carbon steel profile having depth of 110 mm fixed to a stainless steel flat having dimensions of 50x5 mm, fitted on the exposed side, by means of stainless steel M6 screws. The frame is composed of a carbon steel profile having depth of 120 mm fixed, by means of stainless steel M6 screws, to a stainless steel flat, fitted on the exposed side, having dimensions of 30x5 mm. Between the glass faces, the frame, the glass retaining frames and the central mullions, ceramics gaskets, having thickness of 2 mm and sealed by means of silicone type FIRE RETARDING FIRESTOP 700, are fitted. Spacers type PROMATECT H, having dimensions of 20x50x4 mm, are fitted on the lower part between the glass edges and the frame.
The window may also be produced by Naval Suppliers Srl - Zona Industriale 24 - 33049 San Pietro al Natisone (UD) - Italy.

Field of application
Fire resistant A-0 Class window with fire hazard in the inner side of the application.

The surfaces of this division may be fitted with products having low flame spread characteristics, installed as described in the relevant type approval certificates and satisfying the requirements of SOLAS 74 Reg. II-2 as applicable.
Reference documents
HET ANKER BV drawing No. FTW-A0-SQ3-2422 dated 25 May 2009 approved on 5 June 2009 with endorsements No. LABS-281.
Tests carried out
Tests as per RINA Test Laboratory Laboratory report No. 2009CS012333/2 issued on 5 June 2009 issued according to IMO Res. A.754(18) A.I and MSC Circular 727.
As far as applicable, checks and ascertainments have been carried out according to MSC/Circ.1120.




ATTACHMENT TO
CERTIFICATE No. MED388824CS
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****