MED537425CS!002ENG- -  -  N- PBM High-pressure Decorative Laminate Honeycomb Composited Panel -N- S- S- -11/03/2026- Marine Equipment- - SN- S- - N-  - 2,335,696B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED537425CS/002- N-Mar 10, 20312335696
 
Form
  Marine Equipment(TO)
Certification N. MED537425CS/002 - (ENG)
Certificate date 11/03/2026
Type Protezione antincendio
Product Surface materials and floor coverings with low flame-spread characteristics: (a) decorative veneers
Item Nº MED/3.18a
USCG Category N° 164.112

Model or Denomin.
Items
PBM High-pressure Decorative Laminate Honeycomb Composited Panel
Applicant FOSHAN PEARL BUILDING MATERIAL INDUSTRIAL CO., LTD.
Place of requester 89 YONGAN AVENUE, GUANYAO, SHISHAN TOWN, NANHAI DISTRICT Foshan (Guangdong)  % CHINA
Tel. N.,Fax, Email ---, ---, ---
Directive (EU) 2025/1533
Standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.
Reference Documents SOLAS 74 Reg. II-2/3, SOLAS 74 Reg. II-2/5, SOLAS 74 Reg. II-2/6, SOLAS 74 Reg. X/3, IMO Res. MSC.36(63)-(1994 HSC Code) 7,IMO Res. MSC.97(73)-(2000 HSC Code) 7, IMO MSC/Circ.1120.
Request 09/11/2025
Expire date 10/03/2031
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED537425CS/002

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2025/1533.
MED Item Nº MED/3.18a
USCG Category Nº 164.112
Description Surface materials and floor coverings with low flame-spread characteristics: (a) decorative veneers
Type PBM High-pressure Decorative Laminate Honeycomb Composited Panel
Applicant FOSHAN PEARL BUILDING MATERIAL INDUSTRIAL CO., LTD.
89 YONGAN AVENUE, GUANYAO, SHISHAN TOWN, NANHAI DISTRICT Foshan (Guangdong),CHINA
Testing standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.
Reference standards SOLAS 74 Reg. II-2/3, SOLAS 74 Reg. II-2/5, SOLAS 74 Reg. II-2/6, SOLAS 74 Reg. X/3, IMO Res. MSC.36(63)-(1994 HSC Code) 7,IMO Res. MSC.97(73)-(2000 HSC Code) 7, IMO MSC/Circ.1120.
Issued in Genoa on
This Certificate is valid until
March 11, 2026
March 10, 2031
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED537425CS/002
Page 1 of 2

Product description


Aluminium honeycomb panel composed of a hexagonal honeycomb material insulation core 7.2 mm thick (composed of aluminium foil layers with thickness 0.05 mm and side length 6 mm, manufacturer Foshan Pearl Building Material Industrial Co,.Ltd) and, on both sides, an aluminium plate 0.7 mm thick, covered by a high-pressure laminated panel 0.7 mm thick (manufacturer Formica). The aluminium plates are glued to the aluminium honeycomb insulation core and to the laminated panels using dual component isocyanate adhesive type YEBOND 2003 (manufacturer Shanghai Ningrui Adhesives Science & Technology Development Co., Ltd.) in the amount of respectively 300 g/m2 ± 10% and 400 g/m2 ± 10%.
  • Nominal thickness of the panel (mm) 10
  • Nominal mass per area of the panel (kg/m2) 6.2 ± 10%

Field of application

As finishing material for all exposed interior and concealed or inaccessible surfaces (decorative veneer).

The product may be applied to any metallic and non-combustible support if the product would not need any adhesive or combustible material layer.

In case of use on surfaces and linings as specified in paragraph 3.2.1 of SOLAS 1974 Chapter II-2 Reg. 5, where the calorific value shall not exceed 45 MJ/m2 for the thickness used as required in paragraph 3.2.2, the use of the certified product must be evaluated.

Tests carried out

Tests as per SGS-CSTC Standard Technical Services Co., Ltd. Shunde Branch Laboratory reports Nos. SDFTS25008371R02-1 and SDFTS25008371R01-1 dated 27 February 2026 issued according to:
  • IMO 2010 FTP Code Part 5;
  • IMO 2010 FTP Code Part 2.




ATTACHMENT TO
CERTIFICATE No. MED537425CS/002
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****