MED393224CSENGD- -  -  N- SPHD T150P -N- S- S- -14/11/2025- Marine Equipment- - SN- S- - N-  - 25,861B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED393224CS- N-Nov 13, 203025861
 
Form
  Marine Equipment(TO)
Certification N. MED393224CS - (ENG)
Certificate date 14/11/2025
Type Mezzi di salvataggio
Product Launching appliances using falls (davits)
Item Nº MED/1.21

Model or Denomin.
Items
SPHD T150P
Applicant TECNIMPIANTI S.P.A.
Place of requester STRADA CONSORTILE FIUME TORTO - FRAZIONE ZONA INDUSTRIA  %  90018 TERMINI IMERESE (PA)  % ITALY
Tel. N.,Fax, Email 091-8140283, 091-8140325, TECNIMPIANTI@HSOFT.IT
Directive (EU) 2025/1533
Standards IMO Res. MSC 81(70) as amended
Reference Documents Reg. III/4, III/23, III/33, III/34 and Reg. X/3 of SOLAS 74 Convention as amended - IMO Res. MSC.36(63) (1994 HSC Code) 8 - IMO Res. MSC.48(66) (LSA Code) I, VI - IMO Res. MSC.97(73) (2000 HSC Code) 8 - RINA Rules for the certification of Marine Equipment
Request 11/1/2025
Expire date 13/11/2030
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Marco Revello S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED393224CS

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Life-Saving appliances requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2025/1533.
MED Item Nº MED/1.21
Description Launching appliances using falls (davits)
Type SPHD T150P
Applicant TECNIMPIANTI S.P.A.
STRADA CONSORTILE FIUME TORTO - FRAZIONE ZONA INDUSTRIA,90018 TERMINI IMERESE (PA),ITALY
Testing standards IMO Res. MSC 81(70) as amended
Reference standards Reg. III/4, III/23, III/33, III/34 and Reg. X/3 of SOLAS 74 Convention as amended - IMO Res. MSC.36(63) (1994 HSC Code) 8 - IMO Res. MSC.48(66) (LSA Code) I, VI - IMO Res. MSC.97(73) (2000 HSC Code) 8 - RINA Rules for the certification of Marine Equipment
Issued in Genoa on
This Certificate is valid until
November 14, 2025
November 13, 2030
This Certificate consists of this sheet plus an attachment

________________________________________
Fabio Morbioni
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED393224CS
Page 1 of 2

TECHNICAL DATA


The davit is designed for launching tenderboats having maximum load of 260 kN at full complement of equipment and persons (130 kN for each arm). It is also designed for a maximum design hoisting load of 69 kN for each arm. It is a stored power davit with reserve of energy, composed of two arms hinged on a basement welded onto the ship.
The complete rotation of the arms (negative momentum) is forced by hydraulic stored energy. Therefore the movement from the stowed position to the embarkation position and then to the outboard position is obtained by means of hydraulic system which allow the davit to be independent from the main power supply.
REFERENCE DOCUMENTS

Title Appr. no.
Davit assembly STRT-58042
Arm STRT-58043
Fixed frame STRT-58044
Lower block STRT-58045
Safety trace STRT-58046 (only for information)
Cylinder STRT-58047
Schock absorber STRT-58048 (only for information)
Deck sheave C00 STRT-58049
Deck sheave C01 STRT-58050
Transversal section STRT-58051
Maintenance devices STRT-58052 (only for information)
Pendant recovery STRT-58053 (only for information)
Calculation report STRT-58054 (only for information)
Hydraulic diagram booklet PPVT-46608 (only for information)
TESTS CARRIED OUT

In accordance with IMO Resolution MSC.81(70): see test report of 13/10/2025 relevant to job 2024/PA/01/742.




ATTACHMENT TO
CERTIFICATE No. MED393224CS
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Fabio Morbioni
**** NOTICE: This is NOT an official certificate ****