MED094723CS!010ENGD- -  -  N- SRS B0 WET UNIT BULKHEAD -N- S- S- -15/12/2023- Marine Equipment- - SN- S- - N-  - 290,487B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED094723CS/010- N-Dec 14, 2028290487
 
Form
  Marine Equipment(TO)
Certification N. MED094723CS/010 - (ENG)
Certificate date 15/12/2023
Type Protezione antincendio
Product 'A' and 'B' Class divisions fire integrity: (b) 'B' Class divisions
Item Nº MED/3.11b
USCG Category N° 164.108

Model or Denomin.
Items
SRS B0 WET UNIT BULKHEAD
Applicant MARINE INTERIORS CABINS S.P.A.
Place of requester VIA GENOVA 1  %  34121 Trieste (TS)  % ITALY
Tel. N.,Fax, Email ---, ---, ---
Directive (EU) 2023/1667
Standards IMO Res. MSC.307(88)-(2010 FTP Code)
Reference Documents Chap. II-2 of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Request 10/05/2023
Expire date 14/12/2028
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED094723CS/010

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2023/1667.
MED Item Nº MED/3.11b
USCG Category Nº 164.108
Description 'A' and 'B' Class divisions fire integrity: (b) 'B' Class divisions
Type SRS B0 WET UNIT BULKHEAD
Applicant MARINE INTERIORS CABINS S.P.A.
VIA GENOVA 1,34121 Trieste (TS),ITALY
Testing standards IMO Res. MSC.307(88)-(2010 FTP Code)
Reference standards Chap. II-2 of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Issued in Genoa on
This Certificate is valid until
December 15, 2023
December 14, 2028
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED094723CS/010
Page 1 of 2

Product description

Bulkhead having maximum dimensions of 2000 (W) mm x 2160 (H) mm and thickness of 27 mm composed of panels having maximum dimensions of 600 mm (W) x 1960 mm (H). The bulkhead is fitted, in the bottom, with a C shaped steel profile, 2 mm thick and having dimensions of 2000 (W) mm x 200 (H) mm, provided with two holes having diameter of 120 mm and pitch 1000 mm. The panels and the C shaped profile are insulated with one layer of mineral wool with glass fiber cloth type Paroc Fire Slab D180 + N5, 25 mm thick and having density of 180 kg/m3. The panel joints are composed of steel profiles, 0.8 mm thick and having length of 80 mm, with bent edges and screwed (screws 4.8x22 mm and pitch 330 mm) to “omega” shaped steel profiles, 1 mm thick and having length of 88 mm filled with the same mineral wool. The bulkhead is fitted, on the vertical edges and on the upper edge, with C and L shaped steel profiles 1 mm thick, screwed to the steel bulkhead (screws 4.8x22 mm and pitch 330 mm); on the bottom, the bulkhead is screwed to the C shaped steel profile on the joints.
Field of application
Fire resisting B-0 Class bulkhead with fire hazard on the side fitted with the omega shaped steel profiles.
The bulkhead is to be installed with the untested side adjacent to the untested side of another B Class bulkhead ensuring that the level of protection indicated in the relevant fire integrity tables included in SOLAS Chapter II-2/Reg. 9.2 Thermal and Structural Boundaries is always fulfilled.
Reference documents
Santarossa SpA drawing No. 24PC00168 Rev. 1 dated 8 January 2009 approved on 15 January 2009 with endorsement No. LABS-207.

Tests carried out
Tests as per RINA Test Laboratory report No. 2008CS015842/3 issued on 26 January 2009 according to Resolution IMO A.754(18).




ATTACHMENT TO
CERTIFICATE No. MED094723CS/010
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****