MED019624CS!002ENGD- -  -  N- Unisce Marine High Pressure Laminates 3 mm -N- S- S- -25/01/2024- Marine Equipment- - SN- S- - N-  - 1,210,554B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED019624CS/002- N-Jan 24, 20291210554
 
Form
  Marine Equipment(TO)
MED318423WS/002
Certification N. MED019624CS/002 - (ENG)
Certificate date 25/01/2024
Type Protezione antincendio
Product Surface materials and floor coverings with low flame-spread characteristics: (a) decorative veneers
Item Nº MED/3.18a
USCG Category N° 164.112

Model or Denomin.
Items
Unisce Marine High Pressure Laminates 3 mm
Applicant Jiangsu Jiashijia New Material Group Co., Ltd.
Place of requester No.26 Nanmeng Road, Weixin, Economic Zone Changzhou (Jiangsu)  % CHINA
Tel. N.,Fax, Email ---, ---, ---
Directive (EU) 2023/1667
Standards IMO Res. MSC.307(88)-(2010 FTP Code)
Reference Documents Chap. II-2 and X of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Request 17/01/2024
Expire date 24/01/2029
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED019624CS/002

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2023/1667.
MED Item Nº MED/3.18a
USCG Category Nº 164.112
Description Surface materials and floor coverings with low flame-spread characteristics: (a) decorative veneers
Type Unisce Marine High Pressure Laminates 3 mm
Applicant Jiangsu Jiashijia New Material Group Co., Ltd.
No.26 Nanmeng Road, Weixin, Economic Zone Changzhou (Jiangsu),CHINA
Testing standards IMO Res. MSC.307(88)-(2010 FTP Code)
Reference standards Chap. II-2 and X of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Issued in Genoa on
This Certificate is valid until
January 25, 2024
January 24, 2029
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED019624CS/002
Page 1 of 2





Product description

Marine HPL composed of the following layers (starting from the bottom):
  • multiple sheets (22 sheets) of kraft paper impregnated with phenolic resin (mass per area of 250 g/m2 and thickness of 0.13 mm each);
  • decorative paper impregnated with melamine resin (mass per area of 120 g/m2 and thickness of 0.064 mm).


Characteristics of HPL:
  • nominal density 1873 kg/m3 ;
  • nominal thickness 3 mm.


Colour: black or brigher.

Fields of application

As finishing material for all exposed interior and concealed or inaccessible surfaces (decorative veneer).
The product may be applied to any metallic and non-combustible support if the product would not need any adhesive or combustible material layer.
On the basis of the value of the total heat release (Qt) and on the basis of the value of the peak heat release (qp) the material is deemed not generating excessive quantities of smoke nor toxic products in fire according to Annex 2 IMO 2010 FTP Code.
Tests carried out

Tests as per SGS-CSTC Standard Technical Services Co., Ltd. Anji Branch Test Laboratory report No. AJFS2308007089FF dated 23 August 2023 issued according to:
  • IMO 2010 FTP Code Part 5.




ATTACHMENT TO
CERTIFICATE No. MED019624CS/002
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****