MED150725CSENG- -  -  N- RAWCELL® Fiber-PGM -N- S- S- -26/05/2025- Marine Equipment- - SN- S- - N-  - 1,076,762B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED150725CS- N-May 25, 20301076762
 
Form
  Marine Equipment(TO)
Certification N. MED150725CS - (ENG)
Certificate date 26/05/2025
Type Protezione antincendio
Product Surface materials and floor coverings with low flame-spread characteristics: (a) decorative veneers
Item Nº MED/3.18a
USCG Category N° 164.112

Model or Denomin.
Items
RAWCELL® Fiber-PGM
Applicant STARCELL SPA
Place of requester ZONA INDUSTRIALE DI NERICO  %  85020 Pescopagano (PZ)  % ITALY
Tel. N.,Fax, Email 082738951, 082738953, ---
Directive (EU) 2024/1975
Standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.
Reference Documents SOLAS 74 Reg. II-2/3, SOLAS 74 Reg. II-2/5, SOLAS 74 Reg. II-2/6, SOLAS 74 Reg. X/3, IMO Res. MSC.36(63)-(1994 HSC Code) 7,IMO Res. MSC.97(73)-(2000 HSC Code) 7, IMO MSC/Circ.1120.
Request 18/03/2025
Expire date 25/05/2030
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED150725CS

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2024/1975.
MED Item Nº MED/3.18a
USCG Category Nº 164.112
Description Surface materials and floor coverings with low flame-spread characteristics: (a) decorative veneers
Type RAWCELL® Fiber-PGM
Applicant STARCELL SPA
ZONA INDUSTRIALE DI NERICO,85020 Pescopagano (PZ),ITALY
Testing standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.
Reference standards SOLAS 74 Reg. II-2/3, SOLAS 74 Reg. II-2/5, SOLAS 74 Reg. II-2/6, SOLAS 74 Reg. X/3, IMO Res. MSC.36(63)-(1994 HSC Code) 7,IMO Res. MSC.97(73)-(2000 HSC Code) 7, IMO MSC/Circ.1120.
Issued in Genoa on
This Certificate is valid until
May 26, 2025
May 25, 2030
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED150725CS
Page 1 of 2

Product description

Sandwich panel composed of a non-combustible aluminum honeycomb core named NIDO 6006-7018 sheathed on both faces by a fiber glass foil with mineral coating, 0.5 mm thick and having mass per area of 575 g/m2 named Vetro M (manufacturer FICOTEC GMBH). The external foils are glued to the core by means of polyurethane adhesive named HMKL 707.0 in the total amount of 115 g/m².

Thickness (mm) 30

Field of application


As finishing material for all exposed interior and concealed or inaccessible surfaces (decorative veneer).

The product may be applied to any metallic and non-combustible support if the product would not need any adhesive or combustible material layer.

On the basis of the value of the total heat release (Qt) and on the basis of the value of the peak heat release (qp) the material is deemed not generating excessive quantities of smoke nor toxic products in fire according to Annex 2 IMO 2010 FTP Code.
On the basis of the values above the material is exempted from testing in accordance to standard ISO 1716. It will be expected to satisfy a requirement of maximum gross calorific value (e.g., 45 MJ/m2) without further testing.



Tests carried out

Test as per CSI Test Laboratory Report No. 0833\DC\REA\25_2 dated 19 May 2025 issued according to:
  • IMO 2010 FTP Code Part 5.




ATTACHMENT TO
CERTIFICATE No. MED150725CS
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****