MED150625CS!008ENG- -  -  N- GRANIRAPID -N- S- S- -30/05/2025- Marine Equipment- - SN- S- - N-  - 1,113,118B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED150625CS/008- N-May 29, 20301113118
 
Form
  Marine Equipment(TO)
Certification N. MED150625CS/008 - (ENG)
Certificate date 30/05/2025
Type Protezione antincendio
Product Surface materials and floor coverings with low flame-spread characteristics: (a) decorative veneers
Item Nº MED/3.18a
USCG Category N° 164.112

Model or Denomin.
Items
GRANIRAPID
Applicant MAPEI CORPORATION
Place of requester 1144 E.NEWPORT CENTER DRIVE  %  33442 Deerfield (Florida)  % U.S.A.
Tel. N.,Fax, Email 954 485 8575, 954 485 9081, ---
Directive (EU) 2024/1975
Standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.
Reference Documents SOLAS 74 Reg. II-2/3, SOLAS 74 Reg. II-2/5, SOLAS 74 Reg. II-2/6, SOLAS 74 Reg. X/3, IMO Res. MSC.36(63)-(1994 HSC Code) 7,IMO Res. MSC.97(73)-(2000 HSC Code) 7, IMO MSC/Circ.1120.
Request 19/03/2025
Expire date 29/05/2030
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED150625CS/008

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2024/1975.
MED Item Nº MED/3.18a
USCG Category Nº 164.112
Description Surface materials and floor coverings with low flame-spread characteristics: (a) decorative veneers
Type GRANIRAPID
Applicant MAPEI CORPORATION
1144 E.NEWPORT CENTER DRIVE,33442 Deerfield (Florida),U.S.A.
Testing standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.
Reference standards SOLAS 74 Reg. II-2/3, SOLAS 74 Reg. II-2/5, SOLAS 74 Reg. II-2/6, SOLAS 74 Reg. X/3, IMO Res. MSC.36(63)-(1994 HSC Code) 7,IMO Res. MSC.97(73)-(2000 HSC Code) 7, IMO MSC/Circ.1120.
Issued in Genoa on
This Certificate is valid until
May 30, 2025
May 29, 2030
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED150625CS/008
Page 1 of 2

Product description

Adhesive / sealing paste deposited on a non-combustible support.
  • Composition: 63% Sand - 24% Cement - 7% Sulphates - 5% Organic polymers - 1% Cellulose;
  • Thickness: 2.6 mm;
  • Weight: 4200 g/m2 (± 5%)
  • Density: 1600 kg/m3.

The product may be also manufactured by:
MAPEI Corporation, 430 Industrial Dr., West Chicago, IL 60185 - USA

Field of application
The product may be applied to any non-combustible (non metallic) support having a thickness equal to or greater than 25 mm and a density ³ 712.5 kg/m3.

The compliance is valid for the Granirapid by MAPEI having weight of 4200 g/m2 and the relevant tolerance of ± 5% may be applied on the percentages of the components.
Tests carried out
Tests as per LAPI Laboratory Reports No. 947.4IM0080/11, No. 947.4IM0090/11 and No. 947.4IM0100/11 dated 7 September 2011 issued according to:
  • IMO 2010 FTP Code Part 5;
  • IMO 2010 FTP Code Part 2;
  • ISO 1716:2010.




ATTACHMENT TO
CERTIFICATE No. MED150625CS/008
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****