MED288722CSENGB- -  -  N- SINGLE FIRE DOOR WITH OMEGA FRAME -N- S- S- -29/07/2022- Marine Equipment- - SN- S- - N-  - 244,549B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità- MED288722CS- N-Jul 28, 2027244549
 
Form
  Marine Equipment(TO)
MED288722CS
Certification N. MED288722CS - (ENG)
Certificate date 29/07/2022
Type Protezione antincendio
Product Porte tagliafuoco
Item Nº MED/3.16
USCG Category N° 164.136

Model or Denomin.
Items
SINGLE FIRE DOOR WITH OMEGA FRAME
Applicant NAVAL SUPPLIERS SRL
Place of requester ZONA INDUSTRIALE 24  %  33049 SAN PIETRO AL NATISONE (UD)  % ITALY
Tel. N.,Fax, Email 0432 727860, 0432 727886, firedoors@navalsuppliers.com
Directive (EU) 2021/1158
Standards IMO Res. MSC.307(88)-(2010 FTP Code)
Reference Documents Chap. II-2 of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Request 23/6/2022
Expire date 28/07/2027
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED288722CS

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2021/1158.
MED Item Nº MED/3.16
USCG Category Nº 164.136
Description Fire doors
Type SINGLE FIRE DOOR WITH OMEGA FRAME
Applicant NAVAL SUPPLIERS SRL
ZONA INDUSTRIALE 24,33049 SAN PIETRO AL NATISONE (UD),ITALY
Testing standards IMO Res. MSC.307(88)-(2010 FTP Code)
Reference standards Chap. II-2 of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Issued in Genoa on
This Certificate is valid until
July 29, 2022
July 28, 2027
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED288722CS
Page 1 of 2

Product description

Single leaf hinged door whose maximum clear opening size is 1285 mm wide and 2200 mm high. The door leaf, having maximum width of 1332 mm, height of 2217mm and thickness of 50 mm, is composed of two carbon steel sheets, 1.2 mm thick each and, in between, the insulating material. This material is composed of a mineral wool layer type PAROC MARINE FIRE SLAB 200, having thickness of 48 mm and density of 200 kg/m3, glued to the steel sheets by means of 250 g/m2 of adhesive type DUNA CORRADINI AD1670V1. The leaf is fitted, on the perimeter, with C shaped stainless steel profile, 1.2 mm thick and having dimensions of 52.4x15 mm. The door frame is composed of an U shaped steel profile, 5 mm thick and having dimensions of 85x95 mm, fillet welded to the bulkhead. The frame, uninsulated, is fitted, inside, with steel flats, 5 mm thick and, on the corners, an increase of the thickness to 12 mm. The door may be fitted with a stainless steel self-closing hose port having dimensions of 160x188 mm.
Field of application
Fire resistant A-60 Class single leaf hinged door.
In case of doors in compliance to the "Agreement between the European Community and the United States of America", the present certificate is valid at the following conditions:
- doors without windows or with total window area no more than 645 cm2 in each door leaf
- maximum door size tested
- door used with a fire tested frame design
Reference documents
Naval Suppliers drawing No. FT-PA01S-220630 rev. 0 dated 30 June 2022 enclosed to the RINA Test Laboratory report No. 2022CS012887.
Tests carried out
Test as per RINA Test Laboratory report No. 2022CS012887 issued on 29 July 2022 according to IMO 2010 FTP CODE.




ATTACHMENT TO
CERTIFICATE No. MED288722CS
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****