MED552024CS!001ENGD- -  -  N- PORTPAR-PAM-MAXI -N- S- S- -27/01/2025- Marine Equipment- - SN- S- - N-  - 1,152,230B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED552024CS/001- N-Jan 26, 20301152230
 
Form
  Marine Equipment(TO)
Certification N. MED552024CS/001 - (ENG)
Certificate date 27/01/2025
Type Protezione antincendio
Product Porte tagliafuoco
Item Nº MED/3.16
USCG Category N° 164.136

Model or Denomin.
Items
PORTPAR-PAM-MAXI
Applicant MBM GROUP S.R.L.
Place of requester Via Rovereto 4  %  31010 Mareno Di Piave (TV)  % ITALY
Tel. N.,Fax, Email 0422 881716, ---, invoice@mbmgroup.it
Directive (EU) 2024/1975
Standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.
Reference Documents SOLAS 74 Reg.II-2/9, IMO MSC.1/Circ.1511
Request 09/12/2024
Expire date 26/01/2030
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED552024CS/001

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2024/1975.
MED Item Nº MED/3.16
USCG Category Nº 164.136
Description Fire doors
Type PORTPAR-PAM-MAXI
Applicant MBM GROUP S.R.L.
Via Rovereto 4,31010 Mareno Di Piave (TV),ITALY
Testing standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.
Reference standards SOLAS 74 Reg.II-2/9, IMO MSC.1/Circ.1511
Issued in Genoa on
This Certificate is valid until
January 27, 2025
January 26, 2030
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED552024CS/001
Page 1 of 2

Product description


Single leaf hinged door with maximum clear light of 800x1792 mm (WxH). The leaf, having maximum dimensions of 835x1828 mm (WxH) is composed of two steel sheets having, each, thickness of 0.7 mm and, in between, the insulating material. This material is composed of one layer of mineral wool having thickness of 30 mm and density of 150 kg/m3 glued to the steel sheets by means of 250 g/m2 of adhesive named ISOCOLL 8810 FLR or DUNAPOL AD 1670. The leaf is fitted, on the perimeter, with C shaped steel profiles having thickness of 2 mm. The door frame, having thickness of 0.7 mm, is composed of an hollow steel profile insulated with the same mineral wool and reinforced, inside, with C shaped steel profiles. The door is fitted with two closure systems with dog assemblies, one on the upper side and one on the lower side of the leaf; each system acts on two points and is actuated by a key.

The Door may also be produced by:
MBM GROUP SRL Via Rovereto, 4 31010 Mareno di Piave (TV)

Field of application
Fire resistant B-15 Class door.
In case of doors in compliance to the "Agreement between the European Community and the United States of America", the present certificate is valid at the following conditions:
- maximum door size tested
- door used with a fire tested frame design
Reference documents

Mbm drawings No. 2014/PORTPAR-PAM-MAXI rev.1 dated 24 January 2020 approved on 17 April 2020 with endorsement No. LABS-2024.
Tests carried out
Tests as per RINA Test Laboratory report No. 2014CS012797/2 issued on 19 January 2015 according to IMO 2010 FTP Code.




ATTACHMENT TO
CERTIFICATE No. MED552024CS/001
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****