MED471225CS!012ENGD- -  -  N- WB15-MBF-NST DOUBLE BULKHEAD CONFIGURATION -N- S- S- -11/04/2026- Marine Equipment- - SN- S- - N-  - 254,401B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED471225CS/012- N-Apr 10, 2031254401
 
Form
  Marine Equipment(TO)
Certification N. MED471225CS/012 - (ENG)
Certificate date 11/04/2026
Type Protezione antincendio
Product 'A' and 'B' Class divisions fire integrity: (b) 'B' Class divisions
Item Nº MED/3.11b
USCG Category N° 164.108

Model or Denomin.
Items
WB15-MBF-NST DOUBLE BULKHEAD CONFIGURATION
Applicant DE WAVE S.R.L.
Place of requester Via De Marini 60  %  16149 Genova (GE)  % ITALY
Tel. N.,Fax, Email 010-64020886; davide.loria@dewavegroup.com
Directive (EU) 2025/1533
Standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.
Reference Documents SOLAS 74 Reg. II-2/3.4,IMO MSC/Circ. 1120,SOLAS 74 Reg. II-2/9,IMO MSC.1/Circ. 1581
Request 17/10/2025
Expire date 10/04/2031
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED471225CS/012

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2025/1533.
MED Item Nº MED/3.11b
USCG Category Nº 164.108
Description 'A' and 'B' Class divisions fire integrity: (b) 'B' Class divisions
Type WB15-MBF-NST DOUBLE BULKHEAD CONFIGURATION
Applicant DE WAVE S.R.L.
Via De Marini 60,16149 Genova (GE),ITALY
Testing standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.
Reference standards SOLAS 74 Reg. II-2/3.4; IMO MSC/Circ. 1120; SOLAS 74 Reg. II-2/9; IMO MSC.1/Circ. 1581
Issued in Genoa on
This Certificate is valid until
April 11, 2026
April 10, 2031
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED471225CS/012
Page 1 of 2

Product description

Bulkhead composed of two side by side bulkheads installed with, in between, a minimum air gap of 20 mm.
Each bulkhead, consisting of panels having height of 2500 mm and width of 600 mm, is composed starting to the side exposed to the fire of a steel sheet 0,7 mm thick and a steel sheet of 0,3 mm thick on the internal side. In between a mineral wool layer, 25 mm thick and having density of 100 kg/m3 named ULTIMATE U SEA PROTECT produced by SAINT-GOBAIN ISOVER (density of 100 kg/m3) or Rockwool SEAROX SL-420 WAV (density of 120 kg/m3) produced by ROCKWOOL is fitted and glued by means of 110 g/m2 of adhesive ICEMA 145/75. The joints between the panels are made by "L" steel profile bending on the edge of the blades with their respective joints and covered by two steel sheet boxed profile having length of 800 mm each, pitch of 470 mm and dimensions of 52,5x26,6 mm and thickness of 0,6 mm. Between omega and boxed profile a stripe of material type PROMAFLEX GM having dimensions of 2350x120 mm and thickness of 3 mm is fitted. The bulkhead made up of the aforementioned panels is provided on the perimeter of a ā€œCā€ steel profiles 1,2 mm thick with dimensions of 33,5 x 21,5 mm, screwed to the panels on the exposed side to the fire, with pitch of 300 mm on lateral side and 200 mm on upper and lower side. Finaly the panels are provided on the perimeter of two opposing ā€œLā€ profiles with dimensions of 70 x 30 mm and thickness of 2 mm fixed by tack welded on the bulkhead.
Field of application
Fire resisting B-15 Class bulkhead for general application.
Reference documents
De Wave drawing No. DC-01-K1-69 dated 10 May 2019, No. C-01-K1-69 Rev.00 dated 18 July 2020 and No. C-01-K1-42 dated 10 May 2019 approved on 12 April 2021, on 28 July 2020 and on 12 March 2020 respectively with endorsement No. LABS-2217, No. LABS-2063 and No. LABS-2005.
Tests carried out
Tests as per RINA Test Laboratory reports No. 2020CS012316/1 issued on 28 July 2020 and No. 2019CS011692/1 dated 12 March 2020 according to IMO 2010 FTP Code.




ATTACHMENT TO
CERTIFICATE No. MED471225CS/012
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****