MED537525CS!001ENGD- -  -  N- NAVYDAMP ALU -N- S- S- -02/12/2025- Marine Equipment- - SN- S- - N-  - 898,924B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED537525CS/001- N-Dec 1, 2030898924
 
Form
  Marine Equipment(TO)
Certification N. MED537525CS/001 - (ENG)
Certificate date 02/12/2025
Type Protezione antincendio
Product Surface materials and floor coverings with low flame-spread characteristics: (a) decorative veneers
Item Nº MED/3.18a
USCG Category N° 164.112

Model
Items/Sizes
NAVYDAMP ALU
Applicant MAP SPA
Place of requester VIA C. COLOMBO, 15  %  24046 Osio Sotto (BG)  % ITALY
Tel. N.,Fax, Email 0354195201, 0354825528, abergamini@mapspa.com
Directive (EU) 2025/1533
Standard IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.
Reference Documents SOLAS 74 Reg. II-2/3, SOLAS 74 Reg. II-2/5, SOLAS 74 Reg. II-2/6, SOLAS 74 Reg. X/3, IMO Res. MSC.36(63)-(1994 HSC Code) 7,IMO Res. MSC.97(73)-(2000 HSC Code) 7, IMO MSC/Circ.1120.
Request 20/11/2025
Validity 01/12/2030
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED537525CS/001

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2025/1533.
MED Item Nº MED/3.18a
USCG Category Nº 164.112
Description Surface materials and floor coverings with low flame-spread characteristics: (a) decorative veneers
Type NAVYDAMP ALU
Applicant MAP SPA
VIA C. COLOMBO, 15,24046 Osio Sotto (BG),ITALY
Testing standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.
Reference standards SOLAS 74 Reg. II-2/3, SOLAS 74 Reg. II-2/5, SOLAS 74 Reg. II-2/6, SOLAS 74 Reg. X/3, IMO Res. MSC.36(63)-(1994 HSC Code) 7,IMO Res. MSC.97(73)-(2000 HSC Code) 7, IMO MSC/Circ.1120.
Issued in Genoa on
This Certificate is valid until
December 2, 2025
December 1, 2030
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED537525CS/001
Page 1 of 2

Product description



Double viscoelastic self-adhesive coating with constriction layer as follows:
· Viscoelastic butyl type E (thickness 1.4 mm and mass per area 1900 g / m2 ± 12%)
· Honeycomb PP 6610 (thickness 3.2 mm and mass per area 400 g / m2 ± 100)
· Viscoelastic butyl type E (thickness 1.4 mm and mass per area 1900 g / m2 ± 12%)
· 1 mm thick aluminum sheet.

This multilayer product was applied on a metal substrate 3 mm thick.

  • Mass per area (3 mm thick sheet excluded) (g/m2) 6900 ± 10%
  • Thickness (3 mm thick sheet excluded) (mm) 7 ± 1.2



Field of application

As finishing material for all exposed and concealed or inaccessible surfaces. The product may be applied to any metallic support having a thickness ³ 3 mm.
On the basis of the value of the total heat release (Qt) and on the basis of the value of the peak heat release (qp) the material is deemed not generating excessive quantities of smoke nor toxic products in fire according to Annex 2 IMO 2010 FTP Code.

Tests carried out

Test as per RINA Test Laboratory report No. 2020CS013482/1 dated 9 December 2020 issued according to IMO 2010 FTP Code Part. 5.




ATTACHMENT TO
CERTIFICATE No. MED537525CS/001
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****