MED379622CSENGD- -  -  N- A00RS070 -N- S- S- -23/12/2022- Marine Equipment- - SN- S- - N-  - 597,421B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità- MED379622CS- N-Dec 22, 2027597421
 
Form
  Marine Equipment(TO)
Certification N. MED379622CS - (ENG)
Certificate date 23/12/2022
Type Protezione antincendio
Product Porte tagliafuoco
Item Nº MED/3.16
USCG Category N° 164.136

Model
Items/Sizes
A00RS070
Applicant BLU BUD SRL
Place of requester VIA FIESCHI 20/9  %  16121 Genova (GE)  % ITALY
Tel. N.,Fax, Email 0108601379, 0108183053, info@blubud.it
Directive (EU) 2022/1157
Standard IMO Res. MSC.307(88)-(2010 FTP Code)
Reference Documents Chap. II-2 of 1974 SOLAS Convention as amended, RINA Rules for the certification of Marine Equipment
Request 20/9/2022
Validity 22/12/2027
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED379622CS

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2022/1157.
MED Item Nº MED/3.16
USCG Category Nº 164.136
Description Fire doors
Type A00RS070
Applicant BLU BUD
VIA CORSICA 21/20,16121 GENOVA (GE),ITALY
Testing standards IMO Res. MSC.307(88)-(2010 FTP Code)
Reference standards Chap. II-2 of 1974 SOLAS Convention as amended, RINA Rules for the certification of Marine Equipment
Issued in Genoa on
This Certificate is valid until
December 23, 2022
December 22, 2027
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED379622CS
Page 1 of 2

Product description

Roller shutter having maximum clear opening width of 7000 mm and maximum clear opening height of 2500 mm. The roller shutter consists of:
- a shaft;
- a rolled shutter (door leaf);
- two guide channels.
The shutter, made of profiled stripes of stainless steel with width of 71 mm and thickness of 1 mm, is rolled to the shaft and is directed into the guides. The shaft diameter and thickness are, respectively, 168.3 mm and 3 mm. The guide channels are made of 2.5 mm S and L shaped stainless steel profiles fixed together by means of M6 screws and, by means of M8 screws, to an L shaped carbon steel profile, 5 mm thick, welded to the bulkhead. The shutter is fitted, in the middle, lower side, with L shaped steel profile, 5 mm thick and having dimensions of 50x50 mm, equipped with A4-80 steel pin having maximum diameter of 24.5 mm and minimum diameter of 20 mm (shaped as per drawing), inserted when the shutter is closed, in apposite shaped bush, on the sill, having maximum diameter of 31 mm and minimum diameter of 25 mm (shaped as per drawing). In case of maximum width of 4400 mm the door may be equipped, in alternative, with steel pin having diameter of 20 mm and length of 17 mm inserted, when the shutter is closed, in apposite hole, on the sill, having diameter of 24 mm.

Field of application
Fire resistant A-0 Class door.

Reference documents
BLU BUD drawing No. 22057A500 Rev. 4 dated 2 September 2022 enclosed to EFECTIS test report No. EFR-22-G-002518 Rev. 1.
BLU BUD drawing No. 22057A325 Rev. 4 dated 22 December 2022 identified with No. 2022CS013796

Tests carried out
Test as per EFECTIS test laboratory report No. EFR-22-G-002518 Rev. 1 issued on 7 November 2022 according to Part 3 of IMO 2010 FTPC.
Increased dimensions verified with Technical Reports No. 2022/004/MITHP Rev. 0 dated 22 December 2022.




ATTACHMENT TO
CERTIFICATE No. MED379622CS
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****