MED064626CS!001ENGB- -  -  N- PASSAGGI PARATIA GEBERIT MAPRESS STAINLESS STEEL AND CUNIFE -N- S- S- -26/01/2026- Marine Equipment- - SN- S- - N-  - 192,494B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED064626CS/001- N-Jan 25, 2031192494
 
Form
  Marine Equipment(TO)
MED064626CS/001
Certification N. MED064626CS/001 - (ENG)
Certificate date 26/01/2026
Type Protezione antincendio
Product Penetrations through "A" Class divisions: (b) pipe, duct, trunk, etc. penetrations
Item Nº MED/3.26b
USCG Category N° 164.138

Model or Denomin.
Items
PASSAGGI PARATIA GEBERIT MAPRESS STAINLESS STEEL AND CUNIFE
Applicant GEBERIT INTERNATIONAL AG
Place of requester SCHACHENSTRASSE 77  %  CH-8645 JONA  % SWITZERLAND
Tel. N.,Fax, Email +41 552216933, ---, bernd.emmerich@geberit.com
Directive (EU) 2025/1533
Standards IMO Res. MSC.307(88)-(2010 FTP Code) as amended - IMO MSC.1/Circ. 1488
Reference Documents SOLAS 74 Reg.II-2/9, IMO Res. MSC.1/Circ.1276 Rev.1, IMO Res. MSC.1/Circ.1655.
Request 14/06/2021
Expire date 25/01/2031
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED064626CS/001

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2025/1533.
MED Item Nº MED/3.26b
USCG Category Nº 164.138
Description Penetrations through "A" Class divisions: (b) pipe, duct, trunk, etc. penetrations
Type PASSAGGI PARATIA GEBERIT MAPRESS STAINLESS STEEL AND CUNIFE
Applicant GEBERIT INTERNATIONAL AG
SCHACHENSTRASSE 77,CH-8645 JONA,SWITZERLAND
Testing standards IMO Res. MSC.307(88)-(2010 FTP Code) as amended - IMO MSC.1/Circ. 1488
Reference standards SOLAS 74 Reg.II-2/9, IMO Res. MSC.1/Circ.1276 Rev.1, IMO Res. MSC.1/Circ.1655.
Issued in Genoa on
This Certificate is valid until
January 26, 2026
January 25, 2031
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED064626CS/001
Page 1 of 4


Product description


Transits of metallic pipes (CuNiFe - Stainless steel) having diameter ranging from 15 up to 108 mm through bulkheads consisting of carbon steel tubular sections welded to the bulkhead and to the metallic pipes. The pipes and the transits are insulated, when required, with the bulkhead insulation (Paroc Marine Fire Slab 100, 60 mm thick and having density of 100 kg/m3) and, on top, with:
  • mineral wool cylinders type PAROC PRO SECTION 100 or ROCKWOOL PIPE SECTIONS (thickness 30, 70 mm and density 100 kg/m3)
  • mineral wool cylinders type PAROC PRO SECTION 140 or ROCKWOOL PIPE SECTIONS (thickness 70, 120 mm and density 140 kg/m3)
  • mineral wool cylinders sheathed with aluminium foil type ICEROCK DUCTWRAP (thickness 25 mm and density 40-45 kg/m3).
The pipes may be fitted with joints Presfitting type, equipped with butyl rubber gaskets, having length ranging from 48 or 80 mm (pipes with diameter of 15 mm) up to 194 or 310 mm (pipes having diameter of 108 mm); these joints may be installed within 450 mm on each side of the bulkhead.










 



ATTACHMENT TO
CERTIFICATE Nr. MED064626CS/001
Page 2 of 4
Field of application
Fire resistant A Class pipe transits through bulkheads having Class as described in the following tables:
A-0 CLASS
Diameter range (mm)
Insulation on transits / pipes
15-108
-
Note: the transits may be installed on bulkheads fitted without any insulation

A-30 CLASS
Diameter range (mm)
Mineral wool cylinder
(1st layer)
Thick/length/density
Side not exposed (*)
Mineral wool cylinder
(2nd layer)
Thick/length/density
Side not exposed (*)
Mineral wool cylinder

Exposed side
ICEROCK DUCTWRAP
Layers /length
Side not exposed (*)
15-108
30 / 390 / 100
-
-
-
15-108
70 / 390 / 100
-
-
-
15-108
70 / 540 / 100
-
-
-
15-108
70 / 740 / 100
-
-
-
15-108
-
-
-
1st - 540
2nd - 3rd - 240
Note: length is shown in mm – density in kg/m3
(*) The length is intended from the bulkhead insulation

A-60 CLASS
Diameter range (mm)
Mineral wool cylinder
(1st layer)
Thick/length/density
Side not exposed (*)
Mineral wool cylinder
(2nd layer)
Thick/length/density
Side not exposed (*)
Mineral wool cylinder
(1st layer)
Thick/length/density
Exposed side (**)
Mineral wool cylinder
(2nd layer)
Thick/length/density
Exposed side (**)
15-108
30 / 740 / 100
70 /100 /100
-
-
15-108
70 / 540 / 140
120 /240 /140
70 /600 /140
120 / 300 / 140
15
30 / 390 / 100
-
-
-
Note: length is indicated in mm – density in kg/m3
(*) The length is intended from the bulkhead insulation
(**) The length is intended from the bulkhead plate




 



ATTACHMENT TO
CERTIFICATE Nr. MED064626CS/001
Page 3 of 4






Reference documents

Geberit drawings No. 1/11 Rev. 1 (23 sheets) and No. 3/11 Rev. 1 (19 sheets) dated 3 May 2011 approved on 5 May 2011 respectively with endorsement No. LABS-551 and No. LABS-553.


Tests carried out

Tests as per RINA Test Laboratory Reports No. 2010CS014737/1 dated 27 January 2011 and No. 2010CS014737/3 dated 4 April 2011 issued according to IMO Resolution A. 754(18) A.IV.




ATTACHMENT TO
CERTIFICATE No. MED064626CS/001
Pages 4 of 4
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****