MED372726CS!002ENGF- -  -  N- S-WTD A60 -N- S- S- -27/07/2026- Marine Equipment- - SN- S- - N-  - 1,106,188B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED372726CS/002- N-Jul 26, 20311106188
 
Form
  Marine Equipment(TO)
MED013326VE
Certification N. MED372726CS/002 - (ENG)
Certificate date 27/07/2026
Type Protezione antincendio
Product Porte tagliafuoco
Item Nº MED/3.16
USCG Category N° 164.136

Model or Denomin.
Items
S-WTD A60
Applicant GO-TEC Srl
Place of requester Salita Guardia, 60A  %  16014 Ceranesi (GE)  % ITALY
Tel. N.,Fax, Email 0102543514; dscarso@go-tec.it
Directive (EU) 2025/1533
Standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.,IMO MSC.1/Circ.1319
Reference Documents SOLAS 74 Reg. II-2/9,IMO MSC.1/Circ. 1511/Rev.1
Request 31/08/2020
Expire date 26/07/2031
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED372726CS/002

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2025/1533.
MED Item Nº MED/3.16
USCG Category Nº 164.136
Description Fire doors
Type S-WTD A60
Applicant GO-TEC Srl
Salita Guardia, 60A,16014 Ceranesi (GE),ITALY
Testing standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.,IMO MSC.1/Circ.1319
Reference standards SOLAS 74 Reg. II-2/9; IMO MSC.1/Circ. 1511/Rev.1
Issued in Genoa on
This Certificate is valid until
July 27, 2026
July 26, 2031
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED372726CS/002
Page 1 of 2

Product description

Single leaf sliding door with maximum clear light of 2400x2200 mm (WxH). The leaf, having maximum dimensions of 2641x2274 mm (WxH), is composed of a 6 mm thick steel corrugated plate (corrugation dimensions 216x74x53 mm, pitch 538 mm). On the outer side of the sliding guide, two layers of mineral wool panels, (certified non-combustible in conformity to the requirements of the IMO FTP Code) having density of 100 kg/m3, the first having 60 mm thick and the second having 20 mm thick, are shaped to fill the corrugations and a further layer, 60 mm thick, is laid upon the plane formed by the corrugation filling and the plate, glued by means of 200 g/m2 of adhesive type Protopur AE 150. On the inner side of the sliding guide, the corrugation is insulated by one layer of the above mentioned mineral wool panels having thickness 20 mm glued by means of the above mentioned glue. On both side the leaf is covered by one stainless steel sheet with 1 mm of thickness fitted to the door leaf by stainless steel rivets with diameter of 4 mm with a pitch ranging from 350 mm up to 580 mm and glued by means of 200 g/m2 of adhesive type Protopur AE 150. The steel sill, welded to the vertical door frame, thick 20 mm and width 418 mm, contains the guide, 35 mm width and 13 mm height, in which slide three wheels having diameter 130 mm and width 35 mm. In the upper side is provided a steel sliding guide, 20 mm width and 40 mm height bolted to a “C” steel shaped profile thick 6 mm welded to the bulkhead; nine steel brackets 6 mm thick are welded to the “C” shaped profile with a pitch of 292 mm. The vertical leaf edges and door frames are made of a “Ω” steel profile, thick 6 mm; The upper leaf transverse is made by a “C” shaped steel profile with dimensions 267x50 mm thick 4 mm, the lower leaf transverse is made by a steel plate, width 169 mm, thick 4 mm, the upper frame transverse is made by a steel plate, width 148 mm, thick 20 mm. A rebate gasket, Dynamic Service type SIL65/N/T composed by expanded silicon having dimensions 20 x 20 mm is provided on all the door edges, the leaf and frame edges and transverse steel profiles are covered by a welded stainless steel sheet, thick 1 mm. The above mentioned gasket is placed between two layers of intumescent material. The opposite side to the rebate and the upper side of the door are provided with an insulated stainless steel cover, thick 1 mm (thick 2 mm for the upper door cover), with mineral wool panels (certified non-combustible in conformity to the requirements of the IMO FTP Code) 60 mm thick (40 mm thick for the upper side of the door) and having density of 100 kg/m3. The insulation is fitted to the cover by glued steel pins with glue type Sikaflex 291i with a pitch ranging from 300 mm up to 350 mm. On the left vertical mullion of the door is provided an “L” shaped stainless steel profile having dimensions 53 x 36 mm and thickness 1 mm.

Field of application
Fire resistant A-60 Class single leaf sliding door for general application. The door may be installed only on bulkhead side fitted without stiffeners.
In case of doors in compliance to the "Agreement between the European Community and the United States of America", the present certificate is valid at the following conditions:
- doors without windows
- maximum door size tested
- door used with a fire tested frame design

Reference documents
Go-Tec drawing No. P4449-SWTD-00-00-200 4, Rev. 4 dated 10 Jenuary 2021 with endorsement No. LABS-2263 approved on 28 July 2021, Go-Tec drawing No. P4449-SWTD-00-00-201 4, Rev. 4 dated 16 November 2020 with endorsement No. LABS-2266 approved on 28 July 2021, Go-Tec drawing No. P4449-SWTD-00-00-210 0, dated 15 Jenuary 2021 with endorsement No. LABS-2267 approved on 28 July 2021.
Tests carried out
Test as per RINA Test Laboratory reports No. 2020CS01341/1 dated 28 July 2021, No. 2020CS01341/4 dated 28 July 2021, issued according to IMO 2010 FTP Code Part 3.




ATTACHMENT TO
CERTIFICATE No. MED372726CS/002
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****