MED109924CS!005ENG- -  -  N- HSFL B15 -N- S- S- -15/03/2024- Marine Equipment- - SN- S- - N-  - 1,075,374B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED109924CS/005- N-Mar 14, 20291075374
 
Form
  Marine Equipment(TO)
Certification N. MED109924CS/005 - (ENG)
Certificate date 15/03/2024
Type Protezione antincendio
Product Porte tagliafuoco
Item Nº MED/3.16
USCG Category N° 164.136

Model or Denomin.
Items
HSFL B15
Applicant CARETTA SYSTEMS SA
Place of requester THESI PRARI MOUSTAKI  %  19300 Aspropyrgos  % GREECE
Tel. N.,Fax, Email 302105573694, ---, INFO@CARETTA-SYSTEMS.COM
Directive (EU) 2023/1667
Standards IMO Res. MSC.307(88)-(2010 FTP Code) - IMO MSC.1/Circ. 1319
Reference Documents Chap. II-2 of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Request 15/03/2024
Expire date 14/03/2029
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED109924CS/005

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2023/1667.
MED Item Nº MED/3.16
USCG Category Nº 164.136
Description Fire doors
Type HSFL B15
Applicant CARETTA SYSTEMS SA
THESI PRARI MOUSTAKI,19300 Aspropyrgos,GREECE
Testing standards IMO Res. MSC.307(88)-(2010 FTP Code) - IMO MSC.1/Circ. 1319
Reference standards Chap. II-2 of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Issued in Genoa on
This Certificate is valid until
March 15, 2024
March 14, 2029
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED109924CS/005
Page 1 of 2

Product description

Single leaf hinged door whose maximum clear opening dimensions are 1205 mm (W) and 2250 mm (H). The leaf, having maximum width of 1223 mm and maximum height of 2235 mm, is made of a sandwich panel type NEPTUNE BOARD or type CARETTA BOARD composed of two outer moulded surfaces made of magnesia, magnesium chloride and water glass and an internal panel of mineral wool. The outer skins have thickness of 2 mm each and density of 1250 kg/m3; the mineral wool (type ROCKWOOL SEAROX SL450) has thickness of 46 mm and density of 160 kg/m3. Between the two skins, every 200 mm, vertical stiffeners made of the same material as the two skins are fitted.
The internal perimeter of the leaf is fitted with U shaped stainless steel profiles 1.5 mm thick and having dimensions of 40x46x40 mm. The perimeter of the leaf is also fitted with intumescent strips type Kerafix 15x1.5 mm. The door is fitted with a locking system with lock type BMH mod. 1000 DIN18250, two concealed hinges type Tectus 640 3D A8 and a concealed door closer type Dorma ITS 96 4-6. The door frame is composed of steel profiles having thickness of 2 mm, fixed to the bulkhead by means of screws M4x16 mm with pitch of 150 mm. The door frame is completed with a rubber seal type Lorient Batwing LAS1212.
Field of application
Fire resistant B-15 Class single leaf hinged door with the fire hazard on both sides in compliance with IMO MSC.1/Circ. 1319 dated 11 June 2009. In this case the dimensions relevant to the height and width of the door may be increased of 15% provided that the surface area is not increased of more than 10%.

In case of doors in compliance to the "Agreement between the European Community and the United States of America", the present certificate is valid at the following conditions:
- maximum door size tested;
- door used with a fire tested frame design.

The surfaces of this division may be fitted with products having low flame spread characteristics, installed as described in the relevant type approval certificates and satisfying the requirements of SOLAS 74 Reg. II-2 as applicable.

Reference documents
PANMERC ENTERPRISES LTD drawing No. HSF-B15-120 Rev. A dated 5 April 2016 approved on 31 March 2017 with endorsement No. LABS-1443.
Tests carried out
Test as per RINA Test Laboratory report No. 2016CS01980/2 issued on 5 April 2017 according to IMO 2010 FTP Code Part 3.




ATTACHMENT TO
CERTIFICATE No. MED109924CS/005
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****