Product description / Descrizione del prodotto.
Rectangular portlight with or without deadlight 530x730mm.
Portellino di murata rettangolare con o senza corazza 530x730mm.
Reference documents / Documenti di riferimento.
Drawings approved with nr. DIP/129261 and DIP/129262.
Disegni approvati con n° DIP/129261 e DIP/129262.
Tests: technical reports filed with job RS/2024/CS/01/2681.
Prove: rapporto tecnico archiviato su pratica RS/2024/CS/01/2681.
General acceptance conditions / Condizioni di accettazione generali.
1) Shop test: an hydraulic test shall be carried out before despatch by means of batch test. For each batch at least two portlights, within no. 10 portlights produced, shall be tested.
1) Test presso il fabbricante: per ogni lotto deve essere effettuata una pressatura idrostatica prima della spedizione. Per ogni lotto di 10 portellini devono essere collaudati almeno due portellini di murata.
2) The portlight will be supplied from the Manufacturer with installation manual.
2) Il Fabbricante deve fornire il portellino di murata con il manuale di installazione.
Particular acceptance conditions / Condizioni di accettazione particolari.
3) The portlight is suitable for installation on board of yachts having length between perpendicular (corresponding to full load waterline) < 50 m for motor yachts and < 40 m for sailing yachts.
3) Il portellino di murata è idoneo per installazione a bordo di unità aventi lunghezza fra le perpendicolari (corrispondente al galleggiamento di massimo carico) < 50 m per unità a motore e < 40 m per unità a vela.
4) The portlight with remouvable deadlight is suitable for installation in the following zones (see the figure below): 1a, 2a, 1b and 2b. Reference: RINA Rules for the Classification of Yachts Pt. B, Ch. 1, Sec. 1, [5.6].
4) Il portellino con corazza removibile è idoneo per installazione nelle seguenti zone (vedere la figura riportata di seguito): 1a, 2a, 1b and 2b. Riferimento: RINA Rules for the Classification of Yachts Pt. B, Cap. 1, Sez. 1, [5.6].
5) The portlight is suitable, without deadlight, for installation in the following zones (see the figure below): 1a, 2a, 1b and 2b if equivalence between the proposed interlayer and the interlayer foressen by RINA Rules (3mm polycarbonate) will be given to the attending RINA Surveyor.
Reference: RINA Rules for the Classification of Yachts Pt. B, Ch. 1, Sec. 1, [5.6.4] and [5.6.17].
5) Il portellino è idoneo, senza corazza, per installazione nelle seguenti zone (vedere la figura riportata di seguito): 1a, 2a, 1b and 2b se verrà fornita al Tecnico RINA l'equivalenza tra l'interstrato proposto e quello previsto dal regolamento di classe RINA (3mm di policarbonato). Riferimento: RINA Rules for the Classification of Yachts Pt. B, Cap. 1, Sez. 1, [5.6.4] e [5.6.17].
6) For yachts designed for commercial use, the exemption for the use of deadlight in any zone is to be always confirmed by the Flag Authority.
6) Per unità in servizio commerciale, l'esenzione per l'uso della corazza in qualsiasi posizione deve essere sempre confermata dall'Autorità di Bandiera.
7) It is to be verified that the pressures p1, p2 and p3, as calculated according to the rule's formulas, are less than 70 kN/m^2.
7) Deve essere verificato che le pressioni p1, p2 e p3, come calcolate mediante le formule regolamentari, siano inferiori a 70 kN/m^2. |
|