MED631426WS!002ENGD- -  -  N-  HOYHT  -N- S- S- -09/10/2026- Marine Equipment- - SN- S- - N-  - 1,057,304B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED631426WS/002- N-Oct 8, 20311057304
 
Form
  Marine Equipment(TO)
Certification N. MED631426WS/002 - (ENG)
Certificate date 09/10/2026
Type Apparecchi di navigazione
Product Pilot ladder
Item Nº MED/4.49

Model or Denomin.
Items
HOYHT
Applicant DONGTAI CITY HAIOU NAVIGATION EQUIPMENT CO., LTD
Place of requester NO.8 ENVIROMENT PROTECTION&RESCUE EQUIPMENT INDUSTRIAL PARK Dongtai  % CHINA
Tel. N.,Fax, Email 0515-85755586, 0515-85754556, dthohh@126.com
Directive (EU) 2026/1434
Standards IMO Res.A.1045(27), as amended,ISO 799-1:2019.
Reference Documents Reg. V/23 and Reg. X/3 of SOLAS 74 Convention as amended,IMO Res.A.1045(27), IMO MSC/Circ.1428
Request 07/21/2026
Expire date 08/10/2031
Head Office SHANGHAI
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Qiang Sun S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED631426WS/002

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Navigation Equipment requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2026/1434.
MED Item Nº MED/4.49
Description Pilot ladder
Type HOYHT
Applicant DONGTAI CITY HAIOU NAVIGATION EQUIPMENT CO., LTD
NO.8 ENVIROMENT PROTECTION&RESCUE EQUIPMENT INDUSTRIAL PARK Dongtai,CHINA
Testing standards IMO Res.A.1045(27), as amended,ISO 799-1:2019.
Reference standards Reg. V/23 and Reg. X/3 of SOLAS 74 Convention as amended; IMO Res.A.1045(27), IMO MSC/Circ.1428
Issued in SHANGHAI on
This Certificate is valid until
October 9, 2026
October 8, 2031
This Certificate consists of this sheet plus an attachment

________________________________________
Qiang Sun
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED631426WS/002
Page 1 of 2

Product Description


- The pilot ladder is assembled with side rope on each side continuous from the top of the ladder to the
bottom (three-strand rope of polyester and polypropylene blend meeting ISO 1181:2004).

- Each step is supported by each side rope.

- Steps:

The four lowest steps are made of rubber material. L X B X H (534 x 115 x 30, at thinnest point) mm.

The remaining steps except spreader steps are made of composite material. L X B X H (534 x 115 x 26.5 at


thinnest point) mm.

The spreader steps are made of hard wood. L X B X H (1800 x 115 x 26.5, at thinnest point) mm.

- Each side rope has a breaking strength of at least 24 kN.

- Length of ladder: 1.98~35.31 m.


Reference Documents

Technical drawings approved by RINA listed on Approval letter No. : SHFP/2026/1266/ZW002.

Tests Carried Out

- Pilot ladder has been tested in compliance with ISO 799-1:2019, and test report is filed by RINA with
No.: SHFP-39925.

Remarks

- Each ladder is to be marked in compliance with ISO 799-1:2019, Clause 8.

Note

The design assessment is based on ISO799-1:2019, IMO Resolution A.1045(27) and MSC.572(110) & MSC.576(110) (coming into force on 1 January 2028). Operation and Maintenance Manual to be provided on board in compliance with MSC.576(110).

The examination has considered the pilot ladder only, not the installation arrangement. Installation is to be approved on board.

This certificate annuls and replaces the Previous EC Type Examination (Module B) Certificate No.: MED660525WS/002 dated 10/14/2025 due to below modification:


- The side rope is changed from sisal rope to three-strand rope of polyester and polypropylene blend.




ATTACHMENT TO
CERTIFICATE No. MED631426WS/002
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Qiang Sun
**** NOTICE: This is NOT an official certificate ****