MED329022CSENGD- -  -  N- RIVESTIMENTI CON VERNICI A LIQUIDO -N- S- S- -07/11/2022- Marine Equipment- - SN- S- - N-  - 707,147B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità- MED329022CS- N-Nov 6, 2027707147
 
Form
  Marine Equipment(TO)
Certification N. MED329022CS - (ENG)
Certificate date 07/11/2022
Type Protezione antincendio
Product Surface materials and floor coverings with low flame-spread characteristics: (b) paint systems
Item Nº MED/3.18b
USCG Category N° 164.112

Model or Denomin.
Items
RIVESTIMENTI CON VERNICI A LIQUIDO
Applicant ATENA S.P.A.
Place of requester VIA ALCIDE DE GASPERI 52  %  30020 Gruaro (VE)  % ITALY
Tel. N.,Fax, Email 0421 75526, 0421 75692, info@atena-it.com
Directive (EU) 2022/1157
Standards IMO Res. MSC.307(88)-(2010 FTP Code)
Reference Documents Chap. II-2 and X of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Request 01/08/2022
Expire date 06/11/2027
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED329022CS

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2022/1157.
MED Item Nº MED/3.18b
USCG Category Nº 164.112
Description Surface materials and floor coverings with low flame-spread characteristics: (b) paint systems
Type RIVESTIMENTI CON VERNICI A LIQUIDO
Applicant ATENA S.P.A.
VIA ALCIDE DE GASPERI 52,30020 Gruaro (VE),ITALY
Testing standards IMO Res. MSC.307(88)-(2010 FTP Code)
Reference standards Chap. II-2 and X of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Issued in Genoa on
This Certificate is valid until
November 7, 2022
November 6, 2027
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED329022CS
Page 1 of 2

Product description



Painting system composed of 2 layers:
1st layer: two-component epoxy primer named “SERIE 364” produced by “INDUSTRIA COLORI FREDDI S. GIORGIO S.r.l.” (mass per area 250 g/m² ± 20%, thickness: 0.040 mm ± 20%);
2nd layer: two-component matt finish named “SERIE 610” produced by “INDUSTRIA COLORI FREDDI S. GIORGIO S.r.l.” (mass per area: 200 g/m² ± 20%, thickness: 0.040 mm ± 20%).)
  • Mass per area (g/m2): 450 ± 20%
  • Thickness (mm): 0.080 ± 20%


Field of application

As finishing material for all exposed interior and concealed or inaccessible surfaces (paint system).

The product may be applied to any metallic support having a thickness ³ 0.45 mm.
On the basis of the value of the total heat release (Qt) and on the basis of the value of the peak heat release (qp) the material is deemed not generating excessive quantities of smoke nor toxic products in fire according to Annex 2 IMO 2010 FTP Code.

Tests carried out

Tests as per RINA Test Laboratory reports No. 2022CS013290/1 and 2022CS013290/2 dated 7 November 2022 issued according to:
  • IMO 2010 FTP Code Part 5
  • IMO 2010 FTP Code Part 2




ATTACHMENT TO
CERTIFICATE No. MED329022CS
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****