MED566225CS!001ENGD- -  -  N- B15DSG1//B15DSG1A,GLAZED SLIDING DOOR -N- S- S- -10/12/2025- Marine Equipment- - SN- S- - N-  - 597,421B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED566225CS/001- N-Oct 27, 2030597421
 
Form
  Marine Equipment(TO)
Certification N. MED566225CS/001 - (ENG)
Certificate date 10/12/2025
Type Protezione antincendio
Product Porte tagliafuoco
Item Nº MED/3.16

Model or Denomin.
Items
B15DSG1//B15DSG1A,GLAZED SLIDING DOOR
Applicant BLU BUD SRL
Place of requester VIA FIESCHI 20/9  %  16121 Genova (GE)  % ITALY
Tel. N.,Fax, Email 0108601379, 0108183053, info@blubud.it
Directive (EU) 2025/1533
Standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.,IMO MSC.1/Circ.1319
Reference Documents SOLAS 74 Reg.II-2/9, IMO MSC.1/Circ.1511/Rev.1
Request 27/11/2025
Expire date 27/10/2030
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED566225CS/001

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2025/1533.
MED Item Nº MED/3.16
Description Fire doors
Type B15DSG1//B15DSG1A
Applicant BLU BUD SRL
VIA FIESCHI 20/9,16121 Genova (GE),ITALY
Testing standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.,IMO MSC.1/Circ.1319
Reference standards SOLAS 74 Reg.II-2/9, IMO MSC.1/Circ.1511/Rev.1
Issued in Genoa on
This Certificate is valid until
December 10, 2025
October 27, 2030
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED566225CS/001
Page 1 of 2

Product description

Single leaf sliding glazed door having maximum dimensions of 1376x2271 mm (LxH) and clear light of 1300x2200 mm (LxH). The glass compound type PYROBEL 16 EI 30 (manufacturer AGC) having total thickness of 17.3 mm (± 1 mm), is composed of three panes and, in between, two layers of thermo-expanding gel. The door frame is composed of hollow stainless steel profiles having thickness of 1.5 mm type FORSTER, the glass retaining frame, fitted on both side, is composed of hollow stainless steel profiles having dimensions of 20x16.5 mm clipped to the frame. The glass pane is held in place by means of ceramic fiber gaskets having dimensions of 15x4 mm, while on the perimeter edge is fitted a thermoexpanding gasket type FORSTER having dimensions of 24.5x1.5 mm..The door is equipped with closing system with handle and cylinder type TRIOVING 5382/8.
Field of application
Fire resistant B-15 Class single leaf sliding glazed door for general application.

Reference documents
BLU BUD drawing No. B15DSG1.N "Porta B15 con carrelli esposti al fuoco" Rev.1 dated 16 October 2020 approved on 27 October 2020 with endorsement No. LABS-2085 and drawing No. B15DSG1.N "Porta B15 con carrelli non esposti al fuoco" Rev.1 dated 16 October 2020 approved on 27 October 2020 with endorsement No. LABS-2092.
Tests carried out
Test as per RINA Fire Protection Laboratory report No. 2020CS013043/1 issued on 27 October 2020 and No. 2020CS013043/3 issued on 27 October 2020 according to Appendix 1 of IMO 2010 FTPC Part 3.




ATTACHMENT TO
CERTIFICATE No. MED566225CS/001
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****