MED407423CS!003ENG- -  -  N- PORTA TAGLIAFUOCO CLASSE B15 DOPPIA ANTA CON VETRI -N- S- S- -29/11/2023- Marine Equipment- - SN- S- - N-  - 244,549B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED407423CS/003- N-Nov 28, 2028244549
 
Form
  Marine Equipment(TO)
Certification N. MED407423CS/003 - (ENG)
Certificate date 29/11/2023
Type Protezione antincendio
Product Porte tagliafuoco
Item Nº MED/3.16
USCG Category N° 164.136

Model or Denomin.
Items
PORTA TAGLIAFUOCO CLASSE B15 DOPPIA ANTA CON VETRI
Applicant NAVAL SUPPLIERS SRL
Place of requester ZONA INDUSTRIALE 24  %  33049 SAN PIETRO AL NATISONE (UD)  % ITALY
Tel. N.,Fax, Email 0432-727860, 0432-727886, firedoors@navalsuppliers.com
Directive (EU) 2023/1667
Standards IMO Res. MSC.307(88)-(2010 FTP Code) - IMO MSC.1/Circ. 1319
Reference Documents Chap. II-2 of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Request 10/12/2018
Expire date 28/11/2028
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED407423CS/003

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2023/1667.
MED Item Nº MED/3.16
USCG Category Nº 164.136
Description Fire doors
Type PORTA TAGLIAFUOCO CLASSE B15 DOPPIA ANTA CON VETRI
Applicant NAVAL SUPPLIERS SRL
ZONA INDUSTRIALE 24,33049 SAN PIETRO AL NATISONE (UD),ITALY
Testing standards IMO Res. MSC.307(88)-(2010 FTP Code) - IMO MSC.1/Circ. 1319
Reference standards Chap. II-2 of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Issued in Genoa on
This Certificate is valid until
November 29, 2023
November 28, 2028
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED407423CS/003
Page 1 of 2

Product description

Double leaf hinged door with maximum clear light of 2024x2200 mm (WxH). The leaves, having, each, maximum dimensions of 1024x2208 mm (WxH) are composed of two steel sheets, 1.2 mm thick each and, in between, the insulating material composed of a layer of mineral wool (certified non combustible in complaince to 2010 FTP Code), 35 mm thick and having density of 115 kg/m3. The insulating material is glued to the steel sheets by means of 250 g/m2 of adhesive type DUNAPOL AD 1670. The door frame is composed of an hollow steel profile, 1.5 mm thick and having dimensions of 60x69 mm fixed, by means of screws, to a C profile, 2 mm thick and having dimensions of 50x50 mm fixed, by means of screws, to the bulkhead steel sheet. The leaves may be fitted with a circular window having maximum clear light of 350 mm; the glass compound, symmetric, type PYROBELITE 12 (manufacturer AGC) has total thickness of 12 mm. The window frame is composed of stainless steel profiles having thickness of 5 mm and width of 40 mm bolted together by means of M5 screws; between glass and frame stainless steel spacers, 10 mm thick, and gaskets type Forster, having thickness of 2 mm, are fitted. The door is equipped with a closure system, fitted inside, that acts on two points (secondary leaf) and one point (primary leaf).
Field of application
Fire resistant B-15 Class double leaf hinged door in compliance with IMO MSC.1/Circ. 1319 dated 11 June 2009. In this case the dimensions relevant to the height and with of the door may be increased of 15% provided that the surface area is not increased of more than 10%.
In case of doors in compliance to the "Agreement between the European Community and the United States of America", the present certificate is valid at the following conditions:
- doors without windows or with total window area no more than 645 cm2 in each door leaf
- maximum door size tested
- door used with a fire tested frame design
Reference documents
Naval Suppliers drawings No. FT-PTB2-2022-GL dated 5 December 2018 approved on 19 December 2018 with endorsement No. LABS-1789.
Tests carried out
Test as per RINA Test Laboratory reports No. 2018CS012348/7 issued on 19 December 2018 according to IMO 2010 FTP CODE Part 3.




ATTACHMENT TO
CERTIFICATE No. MED407423CS/003
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****