MED660925WSENGD- -  -  N- LNK-PLD-TA -N- S- S- -11/10/2025- Marine Equipment- - SN- S- - N-  - 1,178,895B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED660925WS- N-Oct 10, 20301178895
 
Form
  Marine Equipment(TO)
Certification N. MED660925WS - (ENG)
Certificate date 11/10/2025
Type Apparecchi di navigazione
Product Pilot ladder
Item Nº MED/4.49
USCG Category N° 163.003

Model or Denomin.
Items
LNK-PLD-TA
Applicant XIAMEN LONAKO Inc.
Place of requester Xiamen (Fujian)  % CHINA
Tel. N.,Fax, Email +86-0592-5770062, ---, David@lonako.com
Directive (EU) 2025/1533
Standards IMO Res.A.1045(27), as amended,ISO 799-1:2019.
Reference Documents Reg. V/23 and Reg. X/3 of SOLAS 74 Convention as amended,IMO Res.A.1045(27), IMO MSC/Circ.1428
Request 09/01/2025
Expire date 10/10/2030
Head Office SHANGHAI
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Qiang Sun S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED660925WS

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Navigation Equipment requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2025/1533.
MED Item Nº MED/4.49
USCG Category Nº 163.003
Description Pilot ladder
Type LNK-PLD-TA
Applicant XIAMEN LONAKO Inc.
Xiamen (Fujian),CHINA
Testing standards IMO Res.A.1045(27), as amended,ISO 799-1:2019.
Reference standards Reg. V/23 and Reg. X/3 of SOLAS 74 Convention as amended; IMO Res.A.1045(27), IMO MSC/Circ.1428
Issued in SHANGHAI on
This Certificate is valid until
October 11, 2025
October 10, 2030
This Certificate consists of this sheet plus an attachment

________________________________________
Qiang Sun
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED660925WS
Page 1 of 2
Product Description

- The pilot ladder is assembled with side rope on each side continuous from the top of the ladder to the


bottom (spun thermoset polyester rope with a polypropylene core).

- Each step is supported by each side rope.

- Steps:

The four lowest steps are made of rubber material. LXBXH (533x118x26.5, at thinnest point) mm.

The remaining steps except spreader steps are made of composite material. LXBXH (528x117x26.9, at thinnest


point) mm.

The spreader steps are made of composite material. LXBXH (1805x116x26.9, at thinnest point) mm.

- Each side rope has a breaking strength of at least 24 kN.

- Length of ladder: 2~36m (Steps ≤ 76pcs).

Reference Documents

Appr. Dwg. Title


SHST-48809 Pilot Ladders-LNK-PLD-TA
SHFP-30649 Pilot Ladders-LNK-PLD-TA
SHFP-33965 Pilot Ladders-LNK-PLD-TA
SHFP-33842 Markings of Pilot Ladders-LNK-PLD-TA

Tests Carried Out


- Pilot ladder has been tested in compliance with ISO 799-1:2019, and test report is filed by RINA.

Remarks

- Each ladder is to be marked in compliance with ISO 799-1: 2019, Clause 8.

- Each replacement step is to be marked in compliance with ISO 799-1: 2019, Clause 8.

Note

Renewal of Previous EC Type Examination (Module B) Certificate No.: MED083025WS, with below modification:


- Length of ladder is changed to 2~36m from 3~25m.




ATTACHMENT TO
CERTIFICATE No. MED660925WS
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Qiang Sun
**** NOTICE: This is NOT an official certificate ****