MED171826CS!001ENG- -  -  N- CPLRTV018 -N- S- S- -20/03/2026- Marine Equipment- - NN- S- - N-  - 1,238,142B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED171826CS/001- N-Mar 19, 20311238142
 
Form
  Marine Equipment(TO)
Certification N. MED171826CS/001 - (ENG)
Certificate date 20/03/2026
Type Protezione antincendio
Product Surface materials and floor coverings with low flame-spread characteristics: (d) pipe insulation covers
Item Nº MED/3.18d

Model
Items/Sizes
CPLRTV018
Applicant TEKNOWOOL S.R.L.
Place of requester VIA SAN MARTINO, 54/56  %  20017 Rho (MI)  % ITALY
Tel. N.,Fax, Email ---, ---, o.colajanni@teknowool.com
Directive (EU) 2025/1533
Standard IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.
Reference Documents SOLAS 74 Reg. II-2/3, SOLAS 74 Reg. II-2/5, SOLAS 74 Reg. X/3, IMO Res. MSC.36(63)-(1994 HSC Code) 7, IMO Res. MSC.97(73)-(2000 HSC Code) 7, IMO MSC/Circ.1120
Request 06/03/2026
Validity 19/03/2031
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED171826CS/001

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2025/1533.
MED Item Nº MED/3.18d
Description Surface materials and floor coverings with low flame-spread characteristics: (d) pipe insulation covers
Type CPLRTV018
Applicant TEKNOWOOL S.R.L.
VIA SAN MARTINO, 54/56,20017 Rho (MI),ITALY
Testing standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.
Reference standards SOLAS 74 Reg. II-2/3, SOLAS 74 Reg. II-2/5, SOLAS 74 Reg. X/3, IMO Res. MSC.36(63)-(1994 HSC Code) 7, IMO Res. MSC.97(73)-(2000 HSC Code) 7, IMO MSC/Circ.1120
Issued in Genoa on
This Certificate is valid until
March 20, 2026
March 19, 2031
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED171826CS/001
Page 1 of 2

Product description

Mineral wool circular sections covered on one side with fibre glass fabric named TG-200-FI785 (colour white, nominal mass per area 220 g/m2 ± 10%).
The fabric is glued to the mineral wool by means of single-component glue named Aquagum M/313 or two-component glue named Aquagum B/194 NO FOG, in the quantity of 150 g/m2.
  • Nominal density of the mineral wool (kg/m3): 62 ± 10%
  • Nominal thickness of the mineral wool (mm): 20 up to 80 ± 10%

  • The material may also be produced by:
    Teknowool Sud s.r.l., Via Figurelle 40, 80146 Napoli (NA) - Italy.


    Field of application
    As pipe insulation cover.

    On the basis of the value of the total heat release (Qt) and on the basis of the value of the peak heat release (qp) the material is deemed not generating excessive quantities of smoke nor toxic products in fire according to Annex 2 IMO 2010 FTP Code.
    On the basis of the values above the material is exempted from testing in accordance to standard ISO 1716. It will be expected to satisfy a requirement of maximum gross calorific value (e.g., 45 MJ/m2) without further testing.
    Tests carried out


    Tests as per DBI (Danish Institute of Fire and Security Technology) Test Laboratory reports Nos. PFB10721F, PFB10721H, PFB10721J, PFB10721L, PFB10721P, PFB10721R dated 4 February 2026 issued according to IMO 2010 FTP Code Part 5.




    ATTACHMENT TO
    CERTIFICATE No. MED171826CS/001
    Pages 2 of 2
    The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
    XXXX/YY
    "WHEELMARK FORMAT"

    XXXX
    Notified Body number undertaking surveillance module
    YY
    Last two digits of year mark affixed
         
    ______________________________________________
    General conditions for the approval
    a) The initial conditions verified by RINA at the time of the approval are to be maintained
    b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
    c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
    d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
    e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

    f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


    __________________________________________
    Enrico Cabella
    **** NOTICE: This is NOT an official certificate ****