MED137525CSENGF- -  -  N- FIRE RESISTANT A-60 CLASS DOOR SINGLE LEAF HINGED  -N- S- S- -09/04/2025- Marine Equipment- - SN- S- - N-  - 244,549B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED137525CS- N-Apr 8, 2030244549
 
Form
  Marine Equipment(TO)
Certification N. MED137525CS - (ENG)
Certificate date 09/04/2025
Type Protezione antincendio
Product Porte tagliafuoco
Item Nº MED/3.16
USCG Category N° 164.136

Model or Denomin.
Items
FIRE RESISTANT A-60 CLASS DOOR SINGLE LEAF HINGED
Applicant NAVAL SUPPLIERS SRL Unipersonale
Place of requester ZONA INDUSTRIALE 24  %  33049 San Pietro Al Natisone (UD)  % ITALY
Tel. N.,Fax, Email +39 0432 727860, +39 0432 727886, firedoors@navalsuppliers.com
Directive (EU) 2024/1975
Standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.,IMO MSC.1/Circ.1319
Reference Documents SOLAS 74 Reg.II-2/9, IMO MSC.1/Circ.1511
Request 17/03/2025
Expire date 08/04/2030
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED137525CS

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2024/1975.
MED Item Nº MED/3.16
USCG Category Nº 164.136
Description Fire doors
Type FIRE RESISTANT A-60 CLASS DOOR SINGLE LEAF HINGED
Applicant NAVAL SUPPLIERS SRL Unipersonale
ZONA INDUSTRIALE 24,33049 San Pietro Al Natisone (UD),ITALY
Testing standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.,IMO MSC.1/Circ.1319
Reference standards SOLAS 74 Reg.II-2/9, IMO MSC.1/Circ.1511
Issued in Genoa on
This Certificate is valid until
April 9, 2025
April 8, 2030
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED137525CS
Page 1 of 2

Product description

Single leaf hinged door whose maximum clear opening size is 1400 mm wide and 2400 mm high. The door leaf, having maximum width of 1448 mm, maximum height of 2417 mm and thickness of 50 mm, is composed of two carbon steel sheets, 1.2 mm thick each and, in between the insulating material compound. This compound is composed of a mineral wool layer type Rockwool Searox SL 970 having thickness of 35 mm and density of 115 kg/m3 and a layer of material named PROMAGLAF GM, 12.6 mm thick and having density of 150 kg/m3. The insulating materials are glued together and to the steel sheets by means of 250 g/m2 of adhesive type DUNAPOL AD1670. The leaf is fitted, in the middle, with two C shaped steel stiffeners, 1.2 mm thick and having dimensions of 60x15 mm welded, symmetrically to the two steel sheets, on the upper and lower part of the leaf. The door frame is composed of an S shaped steel profile having thickness of 5 mm, bolted to the bulkhead by means of M8 bolts. The door may be fitted with a self-closing hose port having maximum dimensions of 160x188 mm.
Field of application
Fire resistant A-60 Class single leaf hinged door.
In case of doors in compliance to the "Agreement between the European Community and the United States of America", the present certificate is valid at the following conditions:
- maximum door size tested;
- door used with a fire tested frame design.

The surfaces of this division may be fitted with products having low flame spread characteristics, installed as described in the relevant type approval certificates and satisfying the requirements of SOLAS 74 Reg. II-2 as applicable.
Reference documents
  • Naval Suppliers drawing No. FT-PAZ1S-142415-R00 dated 3 April 2015 approved on 23 April 2015 with endorsement Nos. LABS-1050;
  • Naval Suppliers drawings No. VAR-A60S-3 dated 14 February 2014 and No. VAR-A60S-005 Rev. 2 dated 11 May 2020 approved on 11 May 2020 respectively with endorsement Nos. LABS-2030 and LABS-2031.
Tests carried out
Test as per RINA Test Laboratory report No. 2015CS011147 issued on 23 April 2015 according to IMO 2010 FTP CODE.




ATTACHMENT TO
CERTIFICATE No. MED137525CS
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****