MED071325CS!003ENG- -  -  N- B-15 LINING PANEL (25mm) -N- S- S- -31/03/2025- Marine Equipment- - SN- S- - N-  - 1,083,701B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED071325CS/003- N-Mar 30, 20301083701
 
Form
  Marine Equipment(TO)
Certification N. MED071325CS/003 - (ENG)
Certificate date 31/03/2025
Type Protezione antincendio
Product 'A' and 'B' Class divisions fire integrity: (b) 'B' Class divisions
Item Nº MED/3.11b
USCG Category N° 164.108

Model or Denomin.
Items
B-15 LINING PANEL (25mm)
Applicant MERCAN PANEL URETIM SAN. VE TIC. A.S.
Place of requester ÇERKESLI OSB MAH., IMES BULVARI, No.11 DILOVASI, KOCAELI Kocaeli  % TÜRKIYE
Tel. N.,Fax, Email +90 262 502 0180, +90 262 502 0182, yasinyamac@mercanpanel.com
Directive (EU) 2024/1975
Standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.
Reference Documents IMO Circ. MSC.1 1581,IMO Circ. MSC.1 1120,SOLAS 74 Reg. II-2/3.4,SOLAS 74 Reg. II-2/9
Request 10/02/2025
Expire date 30/03/2030
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED071325CS/003

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2024/1975.
MED Item Nº MED/3.11b
USCG Category Nº 164.108
Description 'A' and 'B' Class divisions fire integrity: (b) 'B' Class divisions
Type B-15 LINING PANEL (25mm)
Applicant MERCAN PANEL URETIM SAN. VE TIC. A.S.
ÇERKESLI OSB MAH., IMES BULVARI, No.11 DILOVASI, KOCAELI Kocaeli,TÜRKIYE
Testing standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.
Reference standards IMO Circ. MSC.1 1581; IMO Circ. MSC.1 1120; SOLAS 74 Reg. II-2/3.4; SOLAS 74 Reg. II-2/9
Issued in Genoa on
This Certificate is valid until
March 31, 2025
March 30, 2030
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED071325CS/003
Page 1 of 2

Product description



Bulkhead having maximum dimension 2212 mm width, 2500 mm height and thick of 25 mm. Bulkhead composed of two side by side bulkheads installed with, in between, a minimum air gap of 100 mm. Each bulkheads, consisting of maximum four panels having maximum width of 550 mm and maximum height of 2500 mm; the panels are composed of two steel sheets, having thickness of 0.6 mm each and with inside one layer of mineral wool Izocam Marine Firebattes 150, recognized as not combustible material as per FTP Code 2010, having a thickness of 25 mm and a density of 150 kg/m3. The mineral wool is glued to the steel sheets by means of 150 g/m2 of glue named Sika Force 710 L100. The panel joint, on the exposed side, consists of “C”shaped steel clip profiles having dimensions of 10x8 mm and thickness of 0.6 mm, on the unexposed side is covered with a steel flat bar having a width of 36 mm and a thickness of 0.6 mm fixed with two steel screws having diameter of 4 mm and pitch of 250 mm. The bulkhead is fitted on the upper side with an "U" shaped steel profile with a thickness of 1.5 mm and dimensions of 60x25x60 mm and on the bottom with a “U” shaped steel profile with a thickness of 1.5 mm having dimensions of 25x25x15 mm and on the side with a "U" shaped steel profile with a thickness of 0.6 mm having dimensions of 25x25x25 mm. These profiles are insulted on the exposed side with a layer of Unifrax FireWrap LT having a thickness of 25 mm and a density of 128 kg/m3.

Field of application

Fire resistant B-15 Class bulkhead for general application.

Due to the fact that this B class bulkhead has been tested from only one side and has been designed to be installed with the untested side adjacent to the untested side of another B class bulkhead, this EC type-examination certificate is valid only if these conditions are respected when installed on board ensuring that the level of protection indicated in the relevant fire integrity tables included in SOLAS Chapter II-2/Reg.9.2 Thermal and Structural Boundaries is always fulfilled.
Reference document
Mercan Panel drawing No. MRN-LWP-M6 dated 16/07/2018 enclosed on the test report No. RFTR18055-REV3 issued on 26/03/2025 identified by No. 2025CS01713/3 attachment No.1 and Mercan Panel drawing No. MRN-LWP-M6 rev.0 dated 07/03/2025 identified by No. 2025CS01713/3 attachment No. 2.


Tests carried out
Tests as per Efectis laboratory test report No. RFTR24044-REV1 issued on 26/03/2025 according to IMO Res. MSC.307(88)-(2010 FTP Code), as amended.




ATTACHMENT TO
CERTIFICATE No. MED071325CS/003
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****