MED460025CSENGB- -  -  N- FIRE DAMPER - TYPE ISOL4 -N- S- S- -12/12/2025- Marine Equipment- - SN- S- - N-  - 698,745B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED460025CS- N-Dec 11, 2030698745
 
Form
  Marine Equipment(TO)
MED460025CS
Certification N. MED460025CS - (ENG)
Certificate date 12/12/2025
Type Protezione antincendio
Product Sbarramenti antincendio
Item Nº MED/3.22
USCG Category N° 164.139

Model
Items/Sizes
FIRE DAMPER  - TYPE ISOL4
Applicant ISOL.ME.CAR. S.R.L.
Place of requester VIA DEI BAGNI NUOVA 5  %  34074 Monfalcone (GO)  % ITALY
Tel. N.,Fax, Email 0481 711895,---, isolmecar@isolmecar.it
Directive (EU) 2025/1533
Standard IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.
Reference Documents SOLAS 74 Reg. II-2/9,IMO MSC.1/Circ.1655.
Request 05/12/2025
Validity 11/12/2030
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED460025CS

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2025/1533.
MED Item Nº MED/3.22
USCG Category Nº 164.139
Description Fire dampers
Type FIRE DAMPER  - TYPE ISOL4
Applicant ISOL.ME.CAR. S.R.L.
VIA DEI BAGNI NUOVA 5,34074 Monfalcone (GO),ITALY
Testing standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.
Reference standards SOLAS 74 Reg. II-2/9; IMO MSC.1/Circ.1655.
Issued in Genoa on
This Certificate is valid until
December 12, 2025
December 11, 2030
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED460025CS
Page 1 of 2

Product description

Multiblade fire dampers having maximum size of 1000x2000 mm (WxH), 300 mm deep fitted, in the middle, with an horizontal flat. The damper frame is composed of a carbon steel plate or stainless steel plate having thickness of 3 mm whereas the blades, having height from 213 up to 298 mm, are composed of an hollow profile made by two carbon steel sheets or stainless steel sheets, 2 mm thick each. The blades are filled with one layer of ceramic fiber (certified non combustible in compliance with IMO FTP Code), having thickness of 19 mm and density of 96 kg/m3. The horizontal flat is composed of a carbon steel or stainless steel flat, having thickness of 3 mm. The dampers installed on bulkheads are fitted with flanges having width of 50 mm; the damper installed on decks are fitted with flanges having width of 30 or 50 mm. Each damper is fitted with two actuators having minimum torque of 12 NM. The A-60 Fire dampers are insulated with one layer of mineral wool (certified non combustible in compliance with IMO FTP Code) having density of 100 kg/m3 and thickness of 60 mm. The mineral wool panels, fixed by means of steel pins and washers, are also applied, on the coaming, for a minimum length of 875 mm.
Field of application
Fire resistant A-0 and A-60 Class fire dampers fitted on bulkheads and on decks.

Reference documents
ISOL.ME.CAR. Srl drawings No. 001/20 Rev. 1 dated 20 November 2020, No. 002/20 dated 20 April 2020, No. 003/20 Rev. 1 dated 20 November 2020 and No. 004/20 dated 20 April 2020 approved on 15 December 2020 respectively with Nos. LABS-2125, LABS-2127, LABS-2128 and LABS-2130.
Tests carried out
Tests as per RINA Test Laboratory Reports No. 2020CS01824/001, No. 2020CS01824/003, No. 2020CS01824/004 and No. 2020CS01824/005 issued on 15 December 2020 according to IMO 2010 FTP Code Part. 3.




ATTACHMENT TO
CERTIFICATE No. MED460025CS
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****