MED261025CSENG- -  -  N- SSFL_A60 LS -N- S- S- -21/05/2025- Marine Equipment- - SN- S- - N-  - 1,075,374B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED261025CS- N-Mar 18, 20291075374
 
Form
  Marine Equipment(TO)
Certification N. MED261025CS - (ENG)
Certificate date 21/05/2025
Type Protezione antincendio
Product Porte tagliafuoco
Item Nº MED/3.16
USCG Category N° 164.136

Model or Denomin.
Items
SSFL_A60 LS
Applicant CARETTA SYSTEMS SA
Place of requester THESI PRARI MOUSTAKI  %  19300 Aspropyrgos  % GREECE
Tel. N.,Fax, Email 302105573694, ---, INFO@CARETTA-SYSTEMS.COM
Directive (EU) 2024/1975
Standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.,IMO MSC.1/Circ.1319
Reference Documents SOLAS 74 Reg.II-2/9, IMO MSC.1/Circ.1511
Request 08/10/2024
Expire date 18/03/2029
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED261025CS

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2024/1975.
MED Item Nº MED/3.16
USCG Category Nº 164.136
Description Fire doors
Type SSFL_A60 LS
Applicant CARETTA SYSTEMS SA
THESI PRARI MOUSTAKI,19300 Aspropyrgos,GREECE
Testing standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.,IMO MSC.1/Circ.1319
Reference standards SOLAS 74 Reg.II-2/9, IMO MSC.1/Circ.1511
Issued in Genoa on
This Certificate is valid until
May 21, 2025
March 18, 2029
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED261025CS
Page 1 of 3

Product description



Single leaf sliding door whose clear opening size is from minimum of 2383x2707 mm (WxH) up to maximum of 3000x5000 mm (WxH) or 5000x3000 mm (WxH). The leaf, having dimensions from minimum of 2497x2719 mm (WxH) up to maximum of 3132x5032 mm (WxH) or 5132x3032 (WxH), is made of one single panel of a composite material. The panel is composed of three skins of material type NEPTUNE SHEET or type CARETTA SHEET, 2 mm thick each and having density of 1250 kg/m3 and, in between, two layers of mineral wool type ROCKWOOL SEAROX SL400-490, 20 mm thick and having density of 160 kg/m3. Vertical stiffeners made of NEPTUNE SHEET or CARETTA SHEET are fitted, between the two skins, every 100 mm. The composite panel edge is contained within two U shaped steel profiles having dimensions 40x42x40x1.25 mm and 30x48x30x1 mm. The edges of the leaf are fitted with intumescent strips type KERAFIX FLEXPAN 200 having dimensions of 15x1.5 mm. The steel sliding guide is 25 mm wide and 24 mm deep with a thickness of 1.4 mm. The sliding guide is supported by steel brackets 6 mm thick, fixed to the bulkhead by means of four M8x40 bolts. At the bottom the door is fitted with two guide rollers. The door with maximum clear opening of 5000x3000 (WxH) is fitted with five thermally activated pins spaced every 750 mm. The door may be fitted with a window having maximum dimensions of 650x650 mm, composed of glass type Pyrobel 25.5 mm thick. The window frame is composed of steel profiles having thickness of 2 mm and 1.25 mm, fitted with ceramic tapes type KERAFIX 30x5 mm and NEPTUNE SHEET or CARETTA SHEET 30x12 mm, and it is fixed to the leaf by means of M6x25 bolts every 180 mm.
The door may be equipped with a self-closing hose port.

Field of application

Fire resistant A-60 Class single leaf sliding door with the fire hazard on both sides in compliance with IMO MSC.1/Circ. 1319 dated 11 June 2009. For doors exceeding 50% in surface area, the installation on board has to be submitted, on a case-by-case basis, to a full analysis based on Solas Regulation II-2/17 (alternative design).

In case of doors in compliance to the "Agreement between the European Community and the United States of America", the present certificate is valid at the following conditions:
- doors without windows or with total window area no more than 645 cm2 in each door leaf;
- maximum door size tested;
- door used with a fire tested frame design.

The surfaces of this division may be fitted with products having low flame spread characteristics, installed as described in the relevant type approval certificates and satisfying the requirements of SOLAS 74 Reg. II-2 as applicable.

 



ATTACHMENT TO
CERTIFICATE Nr. MED261025CS
Page 2 of 3



Reference documents

  • PANMERC ENTERPRISES LTD drawing No. SSF-A60-LS-130 Rev. A dated 17 October 2015 approved on 29 June 2017 with endorsement No. LABS-1486.
  • Only for the window detail: PANMERC ENTERPRISES LTD drawing No. SSF-A60-130 Rev. A dated 30 March 2015 approved on 5 April 2017 with endorsement No. LABS-1455.
Tests carried out

  • Tests as per RINA Test Laboratory Reports No. 2014CS013398/2, 2014CS013398/3 issued on 30 October 2015 according to IMO 2010 FTP Code Part 3.
  • Tests as per RINA Test Laboratory Report No. 2016CS01980/1 issued on 5 April 2017 according to IMO 2010 FTP Code Part 3.
  • Increased dimensions verified with Thermal-Mechanical analysis as per RINA Technical Report No. TR 2017/02/TCHU Rev. 1 dated January 2017.




ATTACHMENT TO
CERTIFICATE No. MED261025CS
Pages 3 of 3
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****