MED416225CS!001ENG- -  -  N- A60 CLASS DOOR SINGLE LEAF HINGED mod. RFID CONNECTA -N- S- S- -28/11/2025- Marine Equipment- - SN- S- - N-  - 244,549B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED416225CS/001- N-Jul 28, 2030244549
 
Form
  Marine Equipment(TO)
Certification N. MED416225CS/001 - (ENG)
Certificate date 28/11/2025
Type Protezione antincendio
Product Porte tagliafuoco
Item Nº MED/3.16
USCG Category N° 164.136

Model or Denomin.
Items
A60 CLASS DOOR SINGLE LEAF HINGED mod. RFID CONNECTA
Applicant NAVAL SUPPLIERS SRL Unipersonale
Place of requester ZONA INDUSTRIALE 24  %  33049 San Pietro Al Natisone (UD)  % ITALY
Tel. N.,Fax, Email +39 0432 727860, +39 0432 727886, firedoors@navalsuppliers.com
Directive (EU) 2025/1533
Standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.,IMO MSC.1/Circ. 1319
Reference Documents SOLAS 74 Reg. II-2/9,IMO MSC.1/Circ. 1511/Rev.1
Request 24/11/2025
Expire date 28/07/2030
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED416225CS/001

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2025/1533.
MED Item Nº MED/3.16
USCG Category Nº 164.136
Description Fire doors
Type A60 CLASS DOOR SINGLE LEAF HINGED mod. RFID CONNECTA
Applicant NAVAL SUPPLIERS SRL Unipersonale
ZONA INDUSTRIALE 24,33049 San Pietro Al Natisone (UD),ITALY
Testing standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.,IMO MSC.1/Circ. 1319
Reference standards SOLAS 74 Reg. II-2/9; IMO MSC.1/Circ. 1511/Rev.1
Issued in Genoa on
This Certificate is valid until
November 28, 2025
July 28, 2030
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED416225CS/001
Page 1 of 3

Product description



Single leaf hinged door with maximum clear opening size of 1200x2200 mm (WxH). The door leaf, having maximum dimensions of 1247x2218 mm (WxH) is composed of two carbon steel sheets, 1.2 mm thick each and, in between, the insulating material. This material is composed of one layer of central layer of mineral wool type Rockwool Searox SL 440, having nominal thickness of 23 mm and nominal density of 150 kg/m3 and, on each side, one layer of material type Promat Pluratect Marine Light, having nominal thickness of 12.5 mm and nominal density of 500 kg/m3. The insulating material is glued to the steel sheets by means of 250 g/m2 of adhesive type DUNA CORRADINI AD1670V1+3200. The leaf is fitted, on the perimeter, with C-shaped stainless steel profile, 1.2 mm thick. The leaf is also fitted with three reinforcement plates next to the perimeter of the leaf. On the two vertical sides of the perimeter, the leaf is insulated also by means of a strip of material type Promat Pluratect Marine Light with dimensions of 45x12.5 mm.
The door frame is composed of a U-shaped steel profile, 5 mm thick and having dimensions of 65x85 mm. The sill is composed of a C-shaped steel profile having dimensions of 25x55 mm and thickness of 5 mm. The frame, on four sides, is welded to the bulkhead. The door may be fitted with a 1.2 mm thick stainless steel self-closing hose port having dimensions of 189x160 mm, insulated as the leaf.
The door is fitted with a lock set type Assa Abloy VingCard Signature Rfid Ble, completed with ethernet lock interface and battery; it is also fitted with connecting cable for the lock.
The leaf may also be fitted with a window having clear light of 400x400 mm. The glass, type Pyroguard T TGU Gel Marine, is contained inside metallic plates screwed on the four sides to the leaf with C-shaped profiles insulated with a strip of Promat Pluratect Marine Light with dimensions of 45x19 mm. Between frame and window strips of Forster 948004 having dimensions of 15x4 mm are present

Field of application

Fire resistant A-60 Class single leaf hinged door with the fire hazard on both sides in compliance with IMO MSC.1/Circ. 1319 dated 11 June 2009. In this case the dimensions relevant to the height and with of the door may be increased of 15% provided that the surface area is not increased of more than 10%.

In case of doors in compliance to the "Agreement between the European Community and the United States of America", the present certificate is valid at the following conditions:
- doors without windows or with total window area no more than 645 cm2 in each door leaf;
- maximum door size tested;
- door used with a fire tested frame design.

The surfaces of this division may be fitted with products having low flame spread characteristics, installed as described in the relevant type approval certificates and satisfying the requirements of SOLAS 74 Reg. II-2 as applicable.



 



ATTACHMENT TO
CERTIFICATE Nr. MED416225CS/001
Page 2 of 3



Reference documents

- Naval Suppliers drawing No. FT_HA61_1200x2200 Rev. 01 dated 29 July 2025 enclosed to the job No. 2025CS012882;
- Naval Suppliers drawing No. FT_HA61_1200x2200 Rev. 00 dated 24 November 2025 enclosed to the job No. 2025CS014162.

Tests carried out

Tests as per RINA Test Laboratory reports:
- No. 2025CS012882/3 dated 29 July 2025;
- No. 2025CS014162/2 dated 28 November 2025 (only for window and lock details),
issued according to IMO 2010 FTP Code Part 3.




ATTACHMENT TO
CERTIFICATE No. MED416225CS/001
Pages 3 of 3
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****