MED113425XP!001ENGD- -  -  N- Pilot Ladder -N- S- S- -08/09/2025- Marine Equipment- - SN- S- - N-  - 0B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED113425XP/001- N-Sep 8, 20300
 
Form
  Marine Equipment(TO)
Certification N. MED113425XP/001 - (ENG)
Certificate date 08/09/2025
Type Apparecchi di navigazione
Product Pilot ladder
Item Nº MED/4.49

Model or Denomin.
Items
Pilot Ladder
Applicant HARBOUR ENTERPRISE LTD.
Place of requester BIRZTALU STREET 6B  %  LV-1015 Riga  % LATVIA
Tel. N.,Fax, Email +371 7 346631, +371 7 343535, sobolevs@harbour.lv
Directive (EU) 2024/1975
Standards IMO Res.A.1045(27), as amended,ISO 799-1:2019.
Reference Documents Reg. V/23, X/3, of SOLAS 74 Convention as amended,IMO Res. A.1045(27), IMO MSC/Circ.1428
Expire date 08/09/2030
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Anna Maria Baranska S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED113425XP/001

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Navigation Equipment requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2024/1975.
MED Item Nº MED/4.49
Description Pilot ladder
Type Pilot Ladder
Applicant HARBOUR ENTERPRISE LTD.
BIRZTALU STREET 6B,LV-1015 Riga,LATVIA
Testing standards IMO Res.A.1045(27), as amended,ISO 799-1:2019.
Reference standards Reg. V/23, X/3, of SOLAS 74 Convention as amended; IMO Res. A.1045(27), IMO MSC/Circ.1428
Issued in Genoa on
This Certificate is valid until
September 8, 2025
September 8, 2030
This Certificate consists of this sheet plus an attachment

________________________________________
Anna Maria Baranska
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED113425XP/001
Page 1 of 2
Product description

Pilot ladder with the following main components:
Hardwood: Lenght: 525 mm - Breadth: 115 mm - Height : 28 mm, 4 holes Ø 24 mm;
Hardwood Spreader step: Lenght: 1800 mm - Breadth: 115 mm - Height: 28 mm, 4 holes Ø 24 mm;
Rubber step: Lenght: 525 mm - Breadth: 115 mm - Height : 28 mm, 4 holes Ø 24 mm;
Manila rope Diameter 22 mm - Minimum breaking strenghth: 24 kN.
Spacing between steps: 330 ± 20 mm
Spacing between side ropes: ≥ 400 mm
Maximum length of ladder: 25 m
Operation and storage temperature: -30 to +65

Reference documents

Maintanance and Use Instruction HE-TD-030/7M/11/PL Rev. 1 dated 15 Jul 2025 issued by Harbour Enterprise Ltd,, filed by RINA with Ref. PLFP/3267
Pilot Ladder Requirements Maintanance and Instruction HE-TD-030/7M/11/PL Annex Rev. 1 dated 15 Jul 2025 issued by Harbour Enterprise Ltd,, filed by RINA with Ref. PLFP/3266
General arrangement and components filed by RINA with Ref. PLFP/3258-PLFP/3263, PLFP/3265
Tests

Test Report for Pilot Ladder dated 26 Aug 2025 witnessed by RINA Survey, filed by RINA under Ref. PLFP/3250
Test Report for Rope No LX20250707007 dated 11 July 2025 issued by Lianxin Testing (Jiangsu) Co. Ltd., filed by RINA under Ref. PLFP/3275

Remarks

A ladder shall not include more than two replacement steps and one replacement spreader step. If a ladder requires third replacement step or a second replacement spreader step, it shall be rebuild.
Each ladder shall be subjected to the ladder and step attachment strength test in Table 2 of ISO 799:2019 at approximately 30 month intervals. Each ladder which fails the test shall be rebuilt or scrapped.

The bottom of the top step and the bottom of the lowest spreader step of the ladder shall be marked as per ISO 799-1:2019 Par 8.1.


The bottom of each replacement step shall be marked as per ISO 799-1:2019 Par 8.2

A permanent marking should be provided at regular intervals (e.g. 1 m) throughout the length of the ladder consistent with ladder design, use and maintenance in order to facilitate the rigging of the ladder to the required height.





ATTACHMENT TO
CERTIFICATE No. MED113425XP/001
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Anna Maria Baranska
**** NOTICE: This is NOT an official certificate ****