MED474525CS!010ENGD- -  -  N- SGSHD 360L -N- S- S- -24/02/2026- Marine Equipment- - SN- S- - N-  - 25,861B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED474525CS/010- N-Feb 23, 203125861
 
Form
  Marine Equipment(TO)
Certification N. MED474525CS/010 - (ENG)
Certificate date 24/02/2026
Type Mezzi di salvataggio
Product Launching appliances using falls (davits)
Item Nº MED/1.21

Model or Denomin.
Items
SGSHD 360L
Applicant TECNIMPIANTI S.P.A.
Place of requester STRADA CONSORTILE FIUME TORTO - FRAZIONE ZONA INDUSTRIALE  %  90018 TERMINI IMERESE (PA)  % ITALY
Tel. N.,Fax, Email 091 8149283, 091 8140325, giorgio.merkouris@tecnimpiantispa.com
Directive (EU) 2025/1533
Standards IMO Res. MSC.81 (70) as amended
Reference Documents Reg. III/4, III/23, III/33, III/34 and Reg. X/3 of SOLAS 74 Convention as amended - IMO Res. MSC.36(63) (1994 HSC Code) 8 - IMO Res. MSC.48(66) (LSA Code) I, VI - IMO Res. MSC.97(73) (2000 HSC Code) 8 - RINA Rules for the certification of Marine Equipment
Request 29/9/2025
Expire date 23/02/2031
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Marco Revello S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED474525CS/010

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Life-Saving appliances requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2025/1533.
MED Item Nº MED/1.21
Description Launching appliances using falls (davits)
Type SGSHD 360L
Applicant TECNIMPIANTI S.P.A.
STRADA CONSORTILE FIUME TORTO - FRAZIONE ZONA INDUSTRIALE,90018 TERMINI IMERESE (PA),ITALY
Testing standards IMO Res. MSC.81 (70) as amended
Reference standards Reg. III/4, III/23, III/33, III/34 and Reg. X/3 of SOLAS 74 Convention as amended - IMO Res. MSC.36(63) (1994 HSC Code) 8 - IMO Res. MSC.48(66) (LSA Code) I, VI - IMO Res. MSC.97(73) (2000 HSC Code) 8 - RINA Rules for the certification of Marine Equipment
Issued in Genoa on
This Certificate is valid until
February 24, 2026
February 23, 2031
This Certificate consists of this sheet plus an attachment

________________________________________
Fabio Morbioni
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED474525CS/010
Page 1 of 2

TECHNICAL DATA

The davit is designed for launching lifeboats having maximum load of 360 kN at full complement of equipment and persons (180 kN for each arm). It is also designed for a maximum design hoisting load of 65 kN for each arm.
The movement from the inboard to the outboard position is obtained by means of an hydraulic system and by gravity which allows the davit to be independent from the main power supply.

REFERENCE DOCUMENTS

Drawing No. Title Appr.No.
981000-13-5011-D Transversal section STRT-22210
981000-64-5042 Workshop pamphlet STRT-22198
981000-64-5041-A Assembly pamphlet STRT-22199-22200
8394 Arm hydraulic cylinder STRT-22193
972500-64-5046 Sheaves pamphlet STRT-22197
8207/B Bowsing hydraulic cylinder STRT-22212
9810-64-5081-0 Launching instructions STRT-22196 (only for information)
9810-64-5037-B Lashing system arrangement STRT-22201 (only for information)
9810-64-5035-C Bowsing system arrangement STRT-22202 (only for information)
9810-64-5034-0 Lifeline for maintenance STRT-22203 (only for information)
9810-64-5032-0 Maintenance devices STRT-22204 (only for information)
9810-64-5031-A Remote control arrangement STRT-22205 (only for information)
9810-64-5022-A Equipment interface STRT-22206 (only for information)
9810-64-5021-C Boats interface STRT-22207 (only for information)
9810-13-5013-C Rescue boat davit STRT-22209 (only for information)

TESTS CARRIED OUT

In accordance with IMO Resolution MSC.81(70); see test report with job 2013/PA/01/494 endorsed with RINA's stamp No.STRT-25879 of 10/10/2014.




ATTACHMENT TO
CERTIFICATE No. MED474525CS/010
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Fabio Morbioni
**** NOTICE: This is NOT an official certificate ****