General description:
The QTVR Range of Trace Heating Units is of the parallel circuit self-regulating type, rated at 230 V
with power output up to 64W/m. The units have a maximum self-limiting temperature of 110°C.
Each trace heating units comprises:
- The active heating cable
- An end seal for terminating the remote end of the unit
- A cable gland for connecting the powered end of the unit to a suitable terminal enclosure , or alternative integrated power connection system.
The active heating cable comprises two stranded copper conductors around which is extruded a semi-conductive core material.
This core material increases in resistance with increasing temperature and gives cable its self-limiting property.
The core is covered with an extruded layer of fluoropolymer insulation before being overbraided with tinned copper.
A further protective, anti-corrosion layer of fluoropolimer is extruded over the braid.
The declared maximum withstand temperature for the range is 110°C and the minimum installation temperature is -60°C.
Cable Accessories:
END SEALS
The end seals for terminating the remote end of the unit may be the following types:
-Type E-100-L-x or E-100-x, which are mechanical end seal incorporating an end cap which is filled with silicone grease sealant
-Type E-20, which comprises heat shrink sleeves lined with hot melt adhesive
-Type E-150 mechanical end seals
SPLICES AND JOINT
The following splicing and jointing arrangement are provided
- A Raychem Type S-20 heat shrink splice kit for connecting lengths of active heating cable.
- A Raychem T-100 tee connection system
- Type S-150 mechanical splice kit
POWER CONNECTION
Power connection may be achieved by the following means:
-Type C25-21. The kits may use a molded silicone rubber core seal to insulate the bus wires with silicone grease in a molded cavity to seal the end of the heating cable.
In this arrangement the kits are Types C25-100 and C16-100
-Type C25-100-Metal, C25-100-Metal-NP, C25-100-Metal-SS, C3/4-100-Metal, C3/4-100-Metal-NP, C3/4-100-Metal-SS, which incorporate a type E8XF metallic cable gland
-Type C-150 power connector
-Type JBS-100 power connection system for a single heater cable
-Type JBM-100 power connection system for multiple heater cables
-Type JBU-100 power connection system
-Type CCON connection kit
TYPE APPROVAL CERTIFICATE
No. ELE052224XG/004
Enclosure - Page 2 of 2
QTVR Series
Special Conditions for Safe Use:
The following limiting temperatures for the end seals , splices and power connections shall not be exceeded:
110°C for the GHG 960 923 p… cable gland S-20, E-20 and CCON
The end seal, splices and power connections have the following associated minimum ambient temperatures:
-55°C for the CCON ;
-50°C for the E-100-x, E-100-L-x , E-150, S-150, C-150, JBS-100, JBU-100 and JBM-100 _
-40°C for the JBS-100-L, JBM-100-L, T100, JBU-100-L,
-55°C for the GHG 960 923 P… cable gland with silicon rubber seals C25-100 and C25-21
-60°C for the type E8XF cable gland, S-20, E-20, C25-100-Metal, C25-100-Metal-NP, C25-100-Metal-SS, C3/4-100-Metal, C3/4-100-Metal-NP, C3/4-100-Metal-SS
Minimum bending radius is 35mm for the type QTVR units.
Thermal output rating: 38 to 64 W/m at 10° C and 230 V
Reference documents:
- ATEX Certificate
Certification Authority: SGS Fimko Oy, Takomotie 8, FI-00380 Helsinki, Finland
Certificates: SGS20ATEX0050X - Isue2
Marking:
II 2 GD Ex 60079-30-1 eb IIC T4 Gb Ex 60079-30-1 eb mb IIC T4 Gb Tmin -60° C or
II 2 GD Ex 60079-30-1 tb IIIC T130°C Ex 60079-30-1 mb tb IIIC T130°C Db
Safety Standard:
EN60079-0: 2018 ; EN60079-7:2015+A1:2018 ; EN60079-18:2015+A1:2017 ; EN60079-30-1:2017
EN60079-31:2014
- Data Sheet: Raychem-DS-EU1381-QTVR-EN
Remarks:
The Information listed in the present certificate are partial information based on the Baseefa Certificates.
The component listed in this Certificate are to be used / installed according to the manufacturer instructions:
Special conditions for safe use and installation to be in accordance with the above referenced ATEX Certificates.
The certificate supersedes previous RINA certificate No. ELE065119XG/004. |
|