MED456224CSENGF- -  -  N- Porta Doppia Anta OMP50A60X.D -N- S- S- -25/10/2024- Marine Equipment- - SN- S- - N-  - 123,543B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED456224CS- N-Jul 23, 2028123543
 
Form
  Marine Equipment(TO)
Certification N. MED456224CS - (ENG)
Certificate date 25/10/2024
Type Protezione antincendio
Product Porte tagliafuoco
Item Nº MED/3.16
USCG Category N° 164.136

Model or Denomin.
Items
Porta Doppia Anta OMP50A60X.D
Applicant MECCANICA MARIANI SRL
Place of requester VIA PIAN DI CELLE. 51  %  05010 San Venanzo (TR)  % ITALY
Tel. N.,Fax, Email 075 875210, 075875557, tecnico@meccanicamariani.it
Directive (EU) 2024/1975
Standards IMO Res. MSC.307(88)-(2010 FTP Code) - IMO MSC.1/Circ. 1319
Reference Documents Chap. II-2 of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Request 09/10/2024
Expire date 23/07/2028
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED456224CS

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2024/1975.
MED Item Nº MED/3.16
USCG Category Nº 164.136
Description Fire doors
Type Porta Doppia Anta OMP50A60X.D
Applicant MECCANICA MARIANI SRL
VIA PIAN DI CELLE. 51,05010 San Venanzo (TR),ITALY
Testing standards IMO Res. MSC.307(88)-(2010 FTP Code) - IMO MSC.1/Circ. 1319
Reference standards Chap. II-2 of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Issued in Genoa on
This Certificate is valid until
October 25, 2024
July 23, 2028
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED456224CS
Page 1 of 3

Product description



Double leaf hinged door with maximum clear opening size of 1500 mm (W) and 1890 mm (H) and having radiused corners with radius of 180 mm. The door leaves, having thickness of 116 mm, maximum height of 1970 mm and maximum width of 610 mm (secondary leaf) and 957.5 (primary leaf), are composed of a steel plate 4 mm thick having the edges bent on the rabbet, of a steel sheet 2 mm thick, fitted in the opposite side. Between the steel plate and the steel sheet is fitted the insulating material composed of two layers of material type PROMAGUARD, 10 and 6 mm thick and having density of 240 kg/m3 fixed to the steel sheet having thickness of 2 mm by means of steel pins and washers welded with density of 15 per m2. The leaves are fitted, inside, with T shaped steel stiffeners having dimensions of 40x40 mm and thickness of 6 mm, welded to the steel plate having thickness of 4 mm. The secondary leaf is equipped with No. 13 stiffeners (12 transversal and 1 longitudinal) whereas inside the primary leaf 16 stiffeners (14 transversal and 2 longitudinal), are fitted. The door frame is composed of a carbon steel angular having dimensions of 100x75x7 mm that makes the closure tight with the gasket fitted in the leaf bent edges. The secondary leaf is fitted with No. 5 external closure points welded to the frame; the primary leaf is equipped with a lever closing device, that acts on 10 points, fitted inside the leaf and actuated by the handle.
The primary leaf may also be fitted with No. 2 external closing points.
























 



ATTACHMENT TO
CERTIFICATE No. MED456224CS
Page 2 of 3


Field of application

Fire resistant A-60 Class double leaf hinged door.
Fire resistant A-30 Class double leaf hinged door in compliance with IMO MSC.1/Circ. 1319 dated 11 June 2009. In this case the dimensions relevant to the height and with of the door may be increased of 15% provided that the surface area is not increased of more than 10%.

In case of doors in compliance to the "Agreement between the European Community and the United States of America", the present certificate is valid at the following conditions:
- maximum door size tested;
- door used with a fire tested frame design.

The surfaces of this division may be fitted with products having low flame spread characteristics, installed as described in the relevant type approval certificates and satisfying the requirements of SOLAS 74 Reg. II-2 as applicable.
Reference documents

- Officina Meccanica Mariani drawing No. OMP50A60X.D dated 6 December 2012 approved on 25 July 2013 with endorsement No. LABS-806.
- Mariani drawing No. R-C351-900-162 dated 24 September 2024 enclosed to job No. 2024CS014562 (for external closing points on the primary leaf).
Tests carried out

Tests as per RINA Test Laboratory Report No. 2013CS012228 issued on 25 July 2013 according to IMO 2010 FTP Code Part 3 and to IMO MSC.1/Circ. 1319 dated 11 June 2009.




ATTACHMENT TO
CERTIFICATE No. MED456224CS
Pages 3 of 3
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****