MED317621CSENGD- -  -  N- A60 BLIND SLIDING DOOR SINGLE LEAF -N- S- S- -22/02/2022- Marine Equipment- - SN- S- - N-  - 597,421B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità- MED317621CS- N-Feb 21, 2027597421
 
Form
  Marine Equipment(TO)
Certification N. MED317621CS - (ENG)
Certificate date 22/02/2022
Type Protezione antincendio
Product Porte tagliafuoco
Item Nº MED/3.16
USCG Category N° 164.136

Model or Denomin.
Items
A60 BLIND SLIDING DOOR SINGLE LEAF
Applicant BLU BUD SRL
Place of requester VIA FIESCHI 20/9  %  16121 Genova (GE)  % ITALY
Tel. N.,Fax, Email 0108601379, 0108183053, info@blubud.it
Directive (EU) 2021/1158
Standards IMO Res. MSC.307(88)-(2010 FTP Code)
Reference Documents Chap. II-2 of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Request 22/06/2021
Expire date 21/02/2027
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED317621CS

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2021/1158.
MED Item Nº MED/3.16
USCG Category Nº 164.136
Description Fire doors
Type A60 BLIND SLIDING DOOR SINGLE LEAF
Applicant BLU BUD SRL
VIA FIESCHI 20/9,16121 Genova (GE),ITALY
Testing standards IMO Res. MSC.307(88)-(2010 FTP Code)
Reference standards Chap. II-2 of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Issued in Genoa on
This Certificate is valid until
February 22, 2022
February 21, 2027
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED317621CS
Page 1 of 2
Product description
Single leaf sliding door whose clear opening size is 1100 mm (W) and 2200 mm (H). The leaf having dimensions of 1219 width, 2280 mm height and 56 mm thick, is composed of two steel sheets, 1 mm thick each and, in between, the insulating material. This material is composed of calcium silicate panels type PROMASIL 1000P 54 mm thick and density of 290 kg/m3 glued to the steel sheet by means of adhesive PROMASEAL Glue. The door frame, composed of a steel profile having thickness of 3 mm and dimensions of 150x90 mm (lock side) and 150x110 mm (opposite side), is fillet welded to the bulkhead. On the upper side is welded to the bulkhead a L steel profile having thickness of 3 mm equipped with suspension trolley that permit to slide the door opening.

Field of application
Fire resistant A-60 Class single leaf sliding door for general application.
In case of doors in compliance to the "Agreement between the European Community and the United States of America", the present certificate is valid at the following conditions:
- doors without windows or with total window area no more than 645 cm2 in each door leaf
- maximum door size tested
- door used with a fire tested frame design
Reference documents
BLU BUD drawing No. 21053A300.RN and 21053A500.RN Rev.0 dated 24 November 2021 enclosed on Test Reports No. 2021CS013176/2 ans 2021CS013176/3.

Tests carried out
Test as per RINA Fire Protection Laboratory report No. 2021CS013176/2 ans 2021CS013176/3 issued on 22 February 2022 according to Appendix 1 of IMO 2010 FTPC Part 3.




ATTACHMENT TO
CERTIFICATE No. MED317621CS
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****