MED237524CS!003ENGD- -  -  N- FLEXIGEL DECORO PREFAB -N- S- S- -25/10/2024- Marine Equipment- - SN- S- - N-  - 379,415B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED237524CS/003- N-Oct 24, 2029379415
 
Form
  Marine Equipment(TO)
Certification N. MED237524CS/003 - (ENG)
Certificate date 25/10/2024
Type Protezione antincendio
Product Surface materials and floor coverings with low flame-spread characteristics: (a) decorative veneers
Item Nº MED/3.18a
USCG Category N° 164.112

Model
Items/Sizes
FLEXIGEL DECORO PREFAB
Applicant API SPA
Place of requester LARGO GUIDO DONEGANI 2  %  20121 Milano (MI)  % ITALY
Tel. N.,Fax, Email ---, ---, ---
Directive (EU) 2024/1975
Standard IMO Res. MSC.307(88)-(2010 FTP Code)
Reference Documents Chap. II-2 and X of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Request 14/05/2024
Validity 24/10/2029
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED237524CS/003

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2024/1975.
MED Item Nº MED/3.18a
USCG Category Nº 164.112
Description Surface materials and floor coverings with low flame-spread characteristics: (a) decorative veneers
Type FLEXIGEL DECORO PREFAB
Applicant API SPA
LARGO GUIDO DONEGANI 2,20121 Milano (MI),ITALY
Testing standards IMO Res. MSC.307(88)-(2010 FTP Code)
Reference standards Chap. II-2 and X of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Issued in Genoa on
This Certificate is valid until
October 25, 2024
October 24, 2029
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED237524CS/003
Page 1 of 2

Product description



Mixture of inorganic fillers, pigments and additives dispersed in hydroxylated polyols.
The cycle involves the application of FLEXIGEL DECORO PREFAB on a steel plate previously treated with PRIMER GREEN.
  • Mass per area FLEXIGEL DECORO PREFAB (g/m2): 2700 ± 100
  • Thickness FLEXIGEL DECORO PREFAB (mm): 2 ± 0.15
  • Mass per area PRIMER GREEN (g/m2): 100 ± 10
  • Thickness PRIMER GREEN (mm): 0.085 ± 0.001


The material may also be produced by:
· API SpA, Regione San Marco 7 - 07041 Alghero - SS - ITALY.
· Stonhard, 7 Esterbrook Lane - Cherry Hill - NJ 08003 - USA.
· Stonhard, 1000 E. Park Ave. - Maple Shade - NJ 08052 - USA.

Field of application

As finishing material for all exposed interior and concealed or inaccessible surfaces (decorative veneer).

The product may be applied to any metallic support having a thickness ³ 2.25 mm.

On the basis of the value of the total heat release (Qt) and on the basis of the value of the peak heat release (qp) the material is deemed not generating excessive quantities of smoke nor toxic products in fire according to Annex 2 IMO 2010 FTP Code.
On the basis of the values above the material is exempted from testing in accordance to standard ISO 1716. It will be expected to satisfy a requirement of maximum gross calorific value (e.g., 45 MJ/m2) without further testing.

Tests carried out

Tests as per RINA Test Laboratory report No. 2024CS012375/4 dated 18 October 2024 issued according to:
  • IMO 2010 FTP Code Part 5




ATTACHMENT TO
CERTIFICATE No. MED237524CS/003
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****