Product description / Descrizione del prodotto
Portlight type VISTAMARE: diam. min 130mm - max 250mm.
Portellino di murata tipo VISTAMARE: diam. min 130mm - max 250mm.
Reference documents / Documenti di riferimento
Drawing approved with nr. DIP/132964 on 11/11/2024.
Disegno approvato con n° DIP/132964 in data 11/11/2024.
Glass: test report 036/25 dated 05/03/2025.
Vetri: rapporto di prova 036/25 datato 05/03/2025.
Metallic structure frame: test report 037/25 dated 05/03/2025.
Telaio struttura metallica: rapporto di prova 037/25 datato 05/03/2025.
Tests: technical reports filed with job nr. RS/2024/CS/01/4844.
Prove: rapporto tecnico archiviato su pratica n° RS/2024/CS/01/4844.
General acceptance conditions / Condizioni di accettazione generali
1) Shop test: an hydraulic test shall be carried out before despatch by means of batch test.
For each batch at least two sidescuttles shall be tested.
1) Test presso il fabbricante: per ogni lotto deve essere effettuata una pressatura idrostatica
prima della spedizione. Per ogni lotto devono essere collaudati almeno due portellini di murata.
2) The sidescuttle will be supplied from the Manufacturer with installation manual.
2) Il Fabbricante deve fornire il portellino di murata con il manuale di installazione.
Particular acceptance conditions / Condizioni di accettazione particolari
3) The sidescuttle is suitable for installation on board of yachts having length between
perpendicular (corresponding to full load waterline) < 50m for motor yachts and < 40m for sailing yachts.
3) Il portellino di murata è idoneo per installazione a bordo di unità aventi lunghezza fra le
perpendicolari (corrispondente al galleggiamento di massimo carico) < 50m per unità a motore e < 40m per unità a vela.
4) The sidescuttle is suitable, without deadlight, for installation in the following zones
(see the figure below): 1a, 2a, 1b and 2b if equivalence between the proposed interlayer and the interlayer
foreseen by RINA Rules (3mm polycarbonate) will be given to the attending RINA Surveyor.
Reference: RINA Rules for the Classification of Yachts Pt. B, Ch. 1, Sec. 1, [5.6.4] and [5.6.17].
4) Il portellino di murata è idoneo, senza corazza, per installazione nelle seguenti zone (vedere la figura riportata di seguito):
1a, 2a, 1b e 2b se verrà fornita al Tecnico RINA l'equivalenza tra l'interstrato proposto e quello previsto dal
regolamento di classe RINA (3mm di policarbonato).
Riferimento: RINA Rules for the Classification of Yachts Pt. B, Cap. 1, Sez. 1, [5.6.4] e [5.6.17].
5) For installation in the following zones (see the figure below): 1a, 2a, 1b and 2b the portlight is to be fixed or not easy
openable. Reference: RINA Rules for the Classification of Yachts Pt. B, Ch. 1, Sec. 1, [5.6.2].
5) Per installazione nelle seguenti zone (vedere la figura riportata di seguito): 1a, 2a, 1b e 2b l'oblò dovrà essere fisso o non
facilmente apribile. Riferimento: RINA Rules for the Classification of Yachts Pt. B, Cap. 1, Sez. 1, [5.6.2].
6) For yachts designed for commercial use, the exemption for the use of deadlight
in any zone is to be always confirmed by the Flag Authority.
6) Per unità in servizio commerciale, l'esenzione per l'uso della corazza in qualsiasi
posizione deve essere sempre confermata dall'Autorità di Bandiera.
7) It is to be verified that the pressures p1, p2 and p3, as calculated according to the
rule's formulas, are less than 70 kN/m^2.
7) Deve essere verificato che le pressioni p1, p2 e p3, come calcolate mediante le formule
regolamentari, siano inferiori a 70 kN/m^2 |
|