MED596225CSENG- -  -  N- LAMPRE PVC RIGIDO MONDOREVIVE  -N- S- S- -06/02/2026- Marine Equipment- - SN- S- - N-  - 552,254B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED596225CS- N-Feb 5, 2031552254
 
Form
  Marine Equipment(TO)
Certification N. MED596225CS - (ENG)
Certificate date 06/02/2026
Type Protezione antincendio
Product Surface materials and floor coverings with low flame-spread characteristics: (a) decorative veneers
Item Nº MED/3.18a
USCG Category N° 164.112

Model or Denomin.
Items
LAMPRE PVC RIGIDO MONDOREVIVE
Applicant LAMPRE SRL
Place of requester VIA A. MAGNI 2  %  20865 Usmate Velate (MB)  % ITALY
Tel. N.,Fax, Email 039674227, 039675018, d.brambilla@lampre.com
Directive (EU) 2025/1533
Standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.
Reference Documents SOLAS 74 Reg. II-2/3, SOLAS 74 Reg. II-2/5, SOLAS 74 Reg. II-2/6, SOLAS 74 Reg. X/3, IMO Res. MSC.36(63)-(1994 HSC Code) 7,IMO Res. MSC.97(73)-(2000 HSC Code) 7, IMO MSC/Circ.1120.
Request 19/12/2025
Expire date 05/02/2031
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED596225CS

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2025/1533.
MED Item Nº MED/3.18a
USCG Category Nº 164.112
Description Surface materials and floor coverings with low flame-spread characteristics: (a) decorative veneers
Type LAMPRE PVC RIGIDO MONDOREVIVE
Applicant LAMPRE SRL
VIA A. MAGNI 2,20865 Usmate Velate (MB),ITALY
Testing standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.
Reference standards SOLAS 74 Reg. II-2/3, SOLAS 74 Reg. II-2/5, SOLAS 74 Reg. II-2/6, SOLAS 74 Reg. X/3, IMO Res. MSC.36(63)-(1994 HSC Code) 7,IMO Res. MSC.97(73)-(2000 HSC Code) 7, IMO MSC/Circ.1120.
Issued in Genoa on
This Certificate is valid until
February 6, 2026
February 5, 2031
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED596225CS
Page 1 of 2

Product description


Rigid PVC film (white color) named PVC-LAM produced by Mondorevive - Busto Arsizio (VA) (mass per area range from 144 to 288 g/m2 ± 10%) glued to a galvanized steel sheet, by means of 9 g/m2 -1 + 2 g/m2 thermoactive polyester-based adhesive produced by Coverplast Srl – Arluno (MI) and named SB174.
  • Film mass per area range (g/m2) from 144 to 288 ± 10%
  • Adhesive mass per area (g/m2) 9 (range - 1 + 2 g/m2 )
  • Film thickness range (mm) from 0.10 to 0.20 ± 10%
  • Adhesive thickness (mm) 0.008

Field of application

As material for all exposed interior and concealed or inaccessible surfaces. The product may be applied to any metallic support having a thickness ³ 0.37 mm.
On the basis of the value of the total heat release (Qt) and on the basis of the value of the peak heat release (qp) the material is deemed not generating excessive quantities of smoke nor toxic products in fire according to Annex 2 IMO IMO 2010 FTP Code.

Tests carried out

Tests as per RINA Test Laboratory reports Nos. 2025CS015962/2, 2025CS015962/3 and 2025CS015962/4 dated 6 February 2026 and 2019CS012977/12 dated 11 November 2019 issued according to:
  • IMO 2010 FTP Code Part. 5;
  • ISO 1716: 2010




ATTACHMENT TO
CERTIFICATE No. MED596225CS
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****