MED281824CSENG- -  -  N- LMD-SL-LORIS 2 -N- S- S- -10/07/2024- Marine Equipment- - SN- S- - N-  - 919,354B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED281824CS- N-Jul 9, 2029919354
 
Form
  Marine Equipment(TO)
Certification N. MED281824CS - (ENG)
Certificate date 10/07/2024
Type Protezione antincendio
Product Porte tagliafuoco
Item Nº MED/3.16
USCG Category N° 164.136

Model or Denomin.
Items
LMD-SL-LORIS 2
Applicant PODSZUCK GMBH
Place of requester KLAUSDORFER WEG 163  %  24148 Kiel  % GERMANY
Tel. N.,Fax, Email +4316611121, +4316611128, ---
Directive (EU) 2023/1667
Standards IMO Res. MSC.307(88)-(2010 FTP Code) - IMO MSC.1/Circ. 1319
Reference Documents Chap. II-2 of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Request 21/01/2019
Expire date 09/07/2029
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED281824CS

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2023/1667.
MED Item Nº MED/3.16
USCG Category Nº 164.136
Description Fire doors
Type LMD-SL-LORIS 2
Applicant PODSZUCK GMBH
KLAUSDORFER WEG 163,24148 Kiel,GERMANY
Testing standards IMO Res. MSC.307(88)-(2010 FTP Code) - IMO MSC.1/Circ. 1319
Reference standards Chap. II-2 of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Issued in Genoa on
This Certificate is valid until
July 10, 2024
July 9, 2029
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED281824CS
Page 1 of 2

Product description



Single leaf sliding door having maximum clear opening size of 5000 mm (W) and 5000 mm (H). The door leaf, having maximum height of 5128 mm and maximum width of 5188 mm, is composed of two parts vertically joined together, by means of a tongue and groove joint which is insulated with strips of PROMATECT H having, each, thickness of 6 mm. The leaf is composed of two steel sheets, 1.5 mm thick each and, in between, the insulating material composed of Neptune sandwich panels having thickness of 47 mm. Such panels consist of three layers of a glass fibre reinforced compound, 2.5 mm thick each, and, in between, two layers of mineral wool which are glued to the steel sheets by means of glue named "Glue K84". The door frame is composed of steel profiles having thickness of 2.5, 3 and 5 mm. The door may be fitted with hose port having maximum dimensions of 220 (W) x 160 (H) mm.
Field of application
Fire resistant single leaf A-60 Class sliding door. For doors exceeding 50% in surface area (15 m2) with respect to the tested doors (2585 x 3887 mm), the installation on board has to be submitted, on a case-by-case basis, also to a full analysis based on Solas Regulation II-2/17 (alternative design).
In case of doors in compliance to the "Agreement between the European Community and the United States of America", the present certificate is valid at the following conditions:
- doors without windows;
- maximum door size tested;
- door used with a fire tested frame design.

Reference documents
Podszuck drawings enclosed to DANAK Test reports No. PG12278 and No. PG12212 dated respectively 15 November 2010 and 27 August 2010 and drawing No. P-10-1304.002.04 dated 2 October 2013 approved on 2 October 2013 with endorsement No. LABS-827.
Tests carried out
Tests as per:
  • DANAK Test reports No. PG12278 dated 15 November 2010 and No. PG12212 dated 27 August 2010 issued according to IMO Resolution A.754(18);
  • DANAK assessment No. PH13633 dated 28 February 2011;
  • RINA Technical Report TR No. 2013/005/TCHD dated 18 September 2013.


This Certificate annuls and replace the previous one No. MED036519CS dated 05/02/2019.




ATTACHMENT TO
CERTIFICATE No. MED281824CS
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****