MED275322CS!001ENGF- -  -  N- FIRE RESISTANT A-60 CLASS DOOR DOUBLE LEAF HINGED BOLTED -N- S- S- -30/06/2022- Marine Equipment- - SN- S- - N-  - 244,549B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità- MED275322CS/001- N-Jun 6, 2027244549
 
Form
  Marine Equipment(TO)
Certification N. MED275322CS/001 - (ENG)
Certificate date 30/06/2022
Type Protezione antincendio
Product Porte tagliafuoco
Item Nº MED/3.16
USCG Category N° 164.136

Model or Denomin.
Items
FIRE RESISTANT A-60 CLASS DOOR DOUBLE LEAF HINGED BOLTED
Applicant NAVAL SUPPLIERS SRL
Place of requester ZONA INDUSTRIALE 24  %  33049 SAN PIETRO AL NATISONE (UD)  % ITALY
Tel. N.,Fax, Email 0432 727860, 0432 727886, firedoors@navalsuppliers.com
Directive (EU) 2021/1158
Standards IMO Res. MSC.307(88)-(2010 FTP Code)
Reference Documents Chap. II-2 of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Request 29/6/2022
Expire date 06/06/2027
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED275322CS/001

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2021/1158.
MED Item Nº MED/3.16
USCG Category Nº 164.136
Description Fire doors
Type FIRE RESISTANT A-60 CLASS DOOR DOUBLE LEAF HINGED BOLTED
Applicant NAVAL SUPPLIERS SRL
ZONA INDUSTRIALE 24,33049 SAN PIETRO AL NATISONE (UD),ITALY
Testing standards IMO Res. MSC.307(88)-(2010 FTP Code)
Reference standards Chap. II-2 of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Issued in Genoa on
This Certificate is valid until
June 30, 2022
June 6, 2027
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED275322CS/001
Page 1 of 2

Product description

Double leaf hinged door whose maximum clear opening size is 2800 mm wide and 2200 mm high. The door leaves, having, each, maximum width of 1421 mm, maximum height of 2217 mm and thickness of 50 mm, are composed of two carbon steel sheets, 1.2 mm thick each and, in between, the insulating material compound. This compound is composed of a mineral wool layer having thickness of 35 mm type SEAROX SL 970 (density of 115 kg/m3) or type PAROC MARINE SLAB 120 (density of 120 kg/m3) and a layer of material named PROMAGLAF GM, 12.6 mm thick and having density of 150 kg/m3. The insulating materials are glued together and to the steel sheets by means of 250 g/m2 of adhesive type DUNAPOL AD1670. Each leaf is fitted, in the middle, with two C shaped steel stiffeners, 1.2 mm thick and having dimensions of 60x15 mm welded, symmetrically to the two steel sheets, on the upper and lower part of the leaf. The secondary leaf is equipped with a lever closing device, that acts on 2 points, fitted inside the leaf and actuated by an handle. The door frame is composed of an S shaped steel profile having thickness of 5 mm, bolted to the bulkhead by means of M8 bolts. The door may be fitted with a self closing hose port having maximum dimensions of 160 x 188 mm.
Field of application
Fire resistant A-60 Class double leaf hinged door.
In case of doors in compliance to the "Agreement between the European Community and the United States of America", the present certificate is valid at the following conditions:
- doors without windows or with total window area no more than 645 cm2 in each door leaf
- maximum door size tested
- door used with a fire tested frame design
Reference documents
Naval Suppliers drawing No. FT-PA6ZI-242215-E1 rev. 1 dated 30 May 2017 approved with endorsement No. LABS-1480 on 7 June 2017.
Tests carried out
Test as per RINA Test Laboratory report No. 2015CS011032 issued on 31 March 2015 according to IMO 2010 FTP CODE. Increased dimensions verified with Technical Report No. 2017/06/TCHU dated May 2017.




ATTACHMENT TO
CERTIFICATE No. MED275322CS/001
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****