MED271823CSENGD- -  -  N- Series 3201-HYDRA ty. 41/C Lift Landing Doors in A-60 Class for Marine Installations -N- S- S- -31/07/2023- Marine Equipment- - SN- S- - N-  - 369,285B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED271823CS- N-Jul 30, 2028369285
 
Form
  Marine Equipment(TO)
Certification N. MED271823CS - (ENG)
Certificate date 31/07/2023
Type Protezione antincendio
Product Porte tagliafuoco
Item Nº MED/3.16
USCG Category N° 164.136

Model or Denomin.
Items
Series 3201-HYDRA ty. 41/C Lift Landing Doors in A-60 Class for Marine Installations
Applicant WITTUR S.P.A.
Place of requester VIA MACEDONIO MELLONI 12  %  43052 Colorno (PR)  % ITALY
Tel. N.,Fax, Email 0521/3111, 0521/311200, ---
Directive (EU) 2022/1157
Standards IMO Res. MSC.307(88)-(2010 FTP Code) - IMO MSC.1/Circ. 1319
Reference Documents Chap. II-2 of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Request 19/07/2023
Expire date 30/07/2028
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED271823CS

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2022/1157.
MED Item Nº MED/3.16
USCG Category Nº 164.136
Description Fire doors
Type Series 3201-HYDRA ty. 41/C Lift Landing Doors in A-60 Class for Marine Installations
Applicant WITTUR S.P.A.
VIA MACEDONIO MELLONI 12,43052 Colorno (PR),ITALY
Testing standards IMO Res. MSC.307(88)-(2010 FTP Code) - IMO MSC.1/Circ. 1319
Reference standards Chap. II-2 of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Issued in Genoa on
This Certificate is valid until
July 31, 2023
July 30, 2028
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED271823CS
Page 1 of 2

Product description

Lift landing door composed of four telescopic sliding leaves having maximum clear opening size of 1600 mm (W) and 2200 mm (H). Each leaf, having maximum height of 2275 mm and maximum width of 446 mm, is composed of a steel sheet with bent edges, 1.5 mm thick, fitted on the side exposed to the fire. The insulating material, composed of two layers of product named GIPSBIFIRE, 12 mm thick each and having density of 880 kg/m3, is at sight on the side not exposed to the fire and is secured by carbon steel sheet retaining clips, fitted on the side of each leaf. The door frame is composed of ā€œCā€ shaped carbon steel profiles having thickness of 3 mm.
Field of application
Fire resistant A-60 Class lift landing door, composed of four telescopic sliding leaves, with fire hazard on side opposite to the suspension trolleys. Fire resistant A-30 Class lift landing door in compliance with IMO MSC.1/Circ. 1319 dated 11 June 2009. In this case the dimensions relevant to the height and with of the door may be increased of 15% provided that the surface area is not increased of more than 10%.
The surfaces of this division, may be fitted with products, having low flame spread characteristics, installed as described in the relevant type approval certificate and satisfying the requirements of SOLAS 74 Reg. II-2 as applicable.
Reference documents
Wittur drawings No. 3201340950 dated 17 July 2013, No. 3201340950V12 dated 2 December 2013 and No. 3201.34.0958 dated 4 March 2016 approved on 30 July 2013, 7 March 2014 and 8 March 2016 respectively with endorsement No. LABS-809, No. LABS-881 and No. LABS-1222.
Tests carried out
Tests as per RINA Test Laboratory Reports No. 2013CS011965 dated 30 July 2013 and No. 2015CS014026 dated 14 January 2016, issued according to IMO 2010 FTP Code Part 3 and to IMO MSC.1/Circ. 1319 dated 11 June 2009.




ATTACHMENT TO
CERTIFICATE No. MED271823CS
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****