MED393026CSENG- -  -  N- FIREROLL A0 -N- S- S- -19/08/2026- Marine Equipment- - NN- S- - N-  - 881,506B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED393026CS- N-Aug 18, 2031881506
 
Form
  Marine Equipment(TO)
Certification N. MED393026CS - (ENG)
Certificate date 19/08/2026
Type Protezione antincendio
Product Porte tagliafuoco
Item Nº MED/3.16
USCG Category N° 164.136

Model
Items/Sizes
FIREROLL A0
Applicant BOLTON GATE COMPANY LIMITED
Place of requester WATERLOO STREET BOLTON BL1 2SP  % UNITED KINGDOM
Tel. N.,Fax, Email ---, ---, ---
Directive (EU) 2025/1533
Standard IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.,IMO MSC.1/Circ.1319
Reference Documents SOLAS 74 Reg.II-2/9, IMO MSC.1/Circ.1511/Rev.1
Request 08/01/2026
Validity 18/08/2031
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED393026CS

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2025/1533.
MED Item Nº MED/3.16
USCG Category Nº 164.136
Description Fire doors
Type FIREROLL A0
Applicant BOLTON GATE COMPANY LIMITED
WATERLOO STREET BOLTON BL1 2SP,UNITED KINGDOM
Testing standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.,IMO MSC.1/Circ.1319
Reference standards SOLAS 74 Reg.II-2/9, IMO MSC.1/Circ.1511/Rev.1
Issued in Genoa on
This Certificate is valid until
August 19, 2026
August 18, 2031
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED393026CS
Page 1 of 3

Product description

Rolling shutter having maximum clear opening of 3600 mm (W) x 2500 mm (H) or maximum clear opening of 6100 mm (W) x 2200 mm (H) installed in a steel bulkhead.

The main component of the rolling shutter are:
- top roller assembly (two roller shafts + a tube);
- a shutter curtain;
- vertical guides assembly (two vertical guide angles + two guide channels);
- a bottom rail;
- protective casing.

The shutter, made of profiled stripes, is rolled to the shafts and is directed into the guides.

The main characteristics of the components are the following:
- shafts having diameter of 31.75 mm and length of 500 mm; tube having thickness of 3 mm and diameter of 133 mm;
- steel interlocking stripes 0.9 mm thick and having maximum width of 51 mm;
- vertical guides made of 3 mm thick steel angle profiles having dimensions of 65 x 50 mm, screwed to the bulkhead by means of M8 screws; guide channels, mounted to each angle profile, having dimensions of 49 x 19 mm (inside) and thickness of 3 mm;
- reinforced bottom rail composed of two steel bars having dimensions of 40 x 6 mm;
- steel protective casing for the roller and the motor.




 



ATTACHMENT TO
CERTIFICATE No. MED393026CS
Page 2 of 3

Field of application
Fire resistant A-0 Class shutter door with the fire hazard on both sides, in compliance with IMO MSC.1/Circ. 1319 dated 11 June 2009. In this case, with regards of the tested dimensions (clear opening of 3600 mm (W) x 2500 mm (H)), the dimensions relevant to the height and width of the door may be increased of 15% provided that the surface area is not increased of more than 10%.

For doors exceeding 50% in surface area with respect to the tested doors, the installation on board has to be submitted, on a case-by-case basis, also to a full analysis based on Solas Regulation II-2/17 (alternative design).

In case of doors in compliance to the "Agreement between the European Community and the United States of America", the present certificate is valid at the following conditions:
- maximum door size tested;
- door used with a fire tested frame design.

The surfaces of this division may be fitted with products having low flame spread characteristics, installed as described in the relevant type approval certificates and satisfying the requirements of SOLAS 74 Reg. II-2 as applicable.

Reference documents

Bolton Gate Company drawings enclosed to DBI Fire and Security Test Laboratory report No. PGB10469A dated 11 September 2025.

Bolton Gate Company drawing "A0 Marine shutter 6100 x 2200 mm" enclosed to the job No. 2026CS013930.

Tests carried out

Test as per DBI Fire and Security Test Laboratory report No. PGB10469A dated 11 September 2025 according to IMO 2010 FTP Code Part 3.

DBI Engineering Assessment of a Marine Steel Fire Shutter No. JOG TIB AAA Version 2 dated 22 June 2026.

RINA Consulting Document Review No. P0048971-H1 Rev.0 dated 15 July 2026.





ATTACHMENT TO
CERTIFICATE No. MED393026CS
Pages 3 of 3
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****