MED343023XGENG- -  -  N- STI-Marine Snap-Seal Cable Plug -N- S- S- -18/01/2024- Marine Equipment- - SN- S- - N-  - 1,050,770B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED343023XG- N-Jan 17, 20291050770
 
Form
  Marine Equipment(TO)
Certification N. MED343023XG - (ENG)
Certificate date 18/01/2024
Type Protezione antincendio
Product Penetrations through "A" Class divisions: (a) electric cable transits
Item Nº MED/3.26a
USCG Category N° 164.138

Model or Denomin.
Items
STI-Marine Snap-Seal Cable Plug
Applicant STI MARINE FIRESTOP. a division of Specified Technologies Inc.
Place of requester 210 Evans Way  %  08876 Somerville (New Jersey)  % U.S.A.
Tel. N.,Fax, Email +19085268000, ---, pschmitt@stimarine.com
Directive (EU) 2023/1667
Standards IMO Res. MSC.307(88)-(2010 FTP Code) - IMO MSC.1/Circ. 1488
Reference Documents Chap. II-2 of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Request 18/12/2017
Expire date 17/01/2029
Head Office Gdańsk
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Daria Orzech S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED343023XG

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2023/1667.
MED Item Nº MED/3.26a
USCG Category Nº 164.138
Description Penetrations through "A" Class divisions: (a) electric cable transits
Type STI-Marine Snap-Seal Cable Plug
Applicant STI MARINE FIRESTOP. a division of Specified Technologies Inc.
210 Evans Way,08876 Somerville (New Jersey),U.S.A.
Testing standards IMO Res. MSC.307(88)-(2010 FTP Code) - IMO MSC.1/Circ. 1488
Reference standards Chap. II-2 of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Issued in Gdańsk on
This Certificate is valid until
January 18, 2024
January 17, 2029
This Certificate consists of this sheet plus an attachment

________________________________________
Anna Maria Baranska
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED343023XG
Page 1 of 3

Product description

Marine Snap Seal Cable Plugs consist of:
- a Ø25mm diameter by 41mm long shell containing intumescent material lining and held by a stainless steel clip used for attachment to divisions.

Field of application

Used in conjunction with A-0 through A-60 Class steel and aluminum bulkheads and A-0 through A-60 Class steel decks with approved insulation arrangements as described below. The A-60 approved copper and pvc tube penetrations may also be used as A-0, A-15 and A-30 Class steel and aluminum bulkheads and decks but shall be insulated as A-60 and in addition the division shall be insulated at least 200 mm around the penetration.



Optional STI MFS Sealant may be installed as an additional continuous seal over Snap-Seal face creating a nominal 2mm film over the face, between Snap-Seal and bulkhead or deck and cable.

Reference documents and tests carried out

Technical drawing HMFP/2984 and STIM0118 test report dated 06/07/2018, filed with letter HMFP/2018/00318/DZU01;
RINA Test report No. 2017CS013044/1 dated 08/02/2018 and filed with No. HMFP/3844;
Test report No. 347336 issue by Exova Test Laboratory dated 12/02/2015 and filed with No. HMFP/3845;
Test report No. 367668 issue by Exova Test Laboratory dated 24/10/2016 and filed with No. HMFP/3846;
Test report No. 380575 issue by Exova Test Laboratory dated 16/05/2017 and filed with No. HMFP/3847;
Test report No. 380576 issue by Exova Test Laboratory dated 16/05/2017 and filed with No. HMFP/3848;
Test report No. 383328 issue by Exova Test Laboratory dated 08/08/2017 and filed with No. HMFP/3849;
Test report No. 389806 issue by Exova Test Laboratory dated 01/12/2017 and filed with No. HMFP/3850;
Test report No. 4786873747 issue by UL Test Laboratory dated 29/04/2015 and filed with No. HMFP/3852;
Test report No. 4788031050 issue by UL Test Laboratory dated 26/06/2017 and filed with No. HMFP/3853;
Test report No. FL-09218-02 issue by Specified Technologies Test Laboratory dated 03/12/2010
and filed with No. HMFP/3854;

Test report No. FL-09218-02 issue by Specified Technologies Test Laboratory dated 03/12/2010
and filed with No. HMFP/3855.




ATTACHMENT TO
CERTIFICATE No. MED343023XG
Pages 3 of 3
Marine Snap Seal Cable Plugs to be installed in place through either side of bulkhead or deck with 0.5 mm thick stainless steel clip. Plug secured with two steel clip tabs, a single screw or single weld according to the installation instructions.

A-0 – A-60 Steel or Aluminum Bulkhead penetration details

Opening (mm)
Fire rating
Division Type
Penetrant
Max Size (mm)
Insulation Detail
Ø27 - 28
A-0 - A-60
Steel and
Aluminum
One or More Cables
Ø 12.4
None
Ø27 - 28
A-60
Steel
Copper tube Ø 6
25mm thickness by 127mm width of STI MPACT Filler Blanket wrapped around tube.
Ø27 - 28
A-60
Steel
PVC tube Ø 6
None

A-0 – A-60 Steel or Aluminum Deck penetration details
Opening (mm)
Fire rating
Division Type
Penetrant
Max Size (mm)
Insulation Detail
Ø27 - 28
A-0 - A-60
Steel and Aluminium
One or More Cable Ø 12.4
None
Ø27 - 28
A-60
Steel
Copper tube Ø 6
25mm thickness by 127mm width of STI MPACT Filler Blanket wrapped around tube.
Ø27 - 28
A-60
Steel
PVC tube Ø 6
None
Production items are to be manufactured in accordance with a quality control system which shall be
maintained to ensure that items are of the same standard as the approved prototype.

Limitations
Filling materials should be adequately secured by bonded materials or mechanical means that cannot be removed without the use of tools in order to prevent damage by normal ship vibrations and pressures.

The pipe penetration/cable transit should not have any visible openings. It should not be possible to manually penetrate any part of the penetration with a 6 mm gap gauge, as described in paragraph 7.10 of annex 1 to part 3 of the 2010 FTP Code.

Acceptance conditions
This Application is not suitable on divisions where watertightness properties are requested.
· The validity of the present certificate is based on the assumption of the constant conformity of the single product manufactured to the prototype that has been tested with positive results to the type approval tests. The firm is responsible in the whole of the above mentioned conformity.
· The holder of the type approval certificate has to inform RINA of any intended modifications to the product and/or manufacturing process which are liable to effect the required conformity of the product.
· The certificate becomes automatically invalid in the following case:
1. the holder of the certificate does not respect the above mentioned obligations.
2. changes have been made to the reference document on which the type approval is based.
· The type approval certificate may be declared suspended or cancelled by RINA when the conditions on which the type approval was based are not fulfilled:







<p STYLE="page-break-after: always">&nbsp;</p>]









ATTACHMENT TO
CERTIFICATE Nr. MED343023XG
Page 3 of 3
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Anna Maria Baranska
**** NOTICE: This is NOT an official certificate ****