MED049824CSENGB- -  -  N- PORTA TAGLIAFUOCO CLASSE A60 DOPPIA ANTA ASIMMETRICA -N- S- S- -12/02/2024- Marine Equipment- - SN- S- - N-  - 244,549B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED049824CS- N-Feb 5, 2029244549
 
Form
  Marine Equipment(TO)
MED049824CS
Certification N. MED049824CS - (ENG)
Certificate date 12/02/2024
Type Protezione antincendio
Product Porte tagliafuoco
Item Nº MED/3.16
USCG Category N° 164.136

Model or Denomin.
Items
PORTA TAGLIAFUOCO CLASSE A60 DOPPIA ANTA ASIMMETRICA
Applicant NAVAL SUPPLIERS SRL
Place of requester ZONA INDUSTRIALE 24  %  33049 SAN PIETRO AL NATISONE (UD)  % ITALY
Tel. N.,Fax, Email 0432-727860, 0432-727886, firedoors@navalsuppliers.com
Directive (EU) 2023/1667
Standards IMO Res. MSC.307(88)-(2010 FTP Code) - IMO MSC.1/Circ. 1319
Reference Documents Chap. II-2 of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Request 12/02/2024
Expire date 05/02/2029
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED049824CS

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2023/1667.
MED Item Nº MED/3.16
USCG Category Nº 164.136
Description Fire doors
Type PORTA TAGLIAFUOCO CLASSE A60 DOPPIA ANTA ASIMMETRICA
Applicant NAVAL SUPPLIERS SRL
ZONA INDUSTRIALE 24,33049 SAN PIETRO AL NATISONE (UD),ITALY
Testing standards IMO Res. MSC.307(88)-(2010 FTP Code) - IMO MSC.1/Circ. 1319
Reference standards Chap. II-2 of SOLAS 74 Convention, as amended, RINA Rules for the certification of Marine Equipment
Issued in Genoa on
This Certificate is valid until
February 12, 2024
February 5, 2029
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED049824CS
Page 1 of 2

Product description

Double leaf hinged door whose maximum clear opening size is 2400 mm wide and 2400 mm high. The primary leaf has maximum width of 1621 mm and maximum height of 2417 mm; the secondary leaf has maximum width of 821 mm and maximum height of 2417 mm. The door leaves, having thickness of 62,4 mm, are composed of two carbon steel sheets, 1.2 mm thick each and, in between the insulating material composed of one layer of mineral wool (certified non combustible in compliance to 2010 FTP Code), 60 mm thick and having density of 180 kg/m3. The insulating material is glued to the steel sheets by means of 250 g/m2 of adhesive type DUNA CORRADINI AD 1670. The primary leaf is fitted, in the middle, with two C shaped steel stiffeners, 1.2 mm thick and having dimensions of 60x20 mm welded, symmetrically, to the two steel sheets on the upper and lower part of the leaf. The secondary leaf is equipped with a lever closing device, which acts on two points, fitted inside the leaf and actuated by an handle. The primary leaf is fitted with a lever closing device, which acts on three points, fitted inside the leaf and actuated by an handle. The door frame is composed of an S shaped steel profile having thickness of 5 mm, welded or bolted to the bulkhead by means of M8 bolts fitted with pitch of 450 mm. The door may be fitted with a self-closing hose port having maximum dimensions of 188x160 mm.
Field of application
Fire resistant A-60 Class double leaf hinged door in compliance with IMO MSC.1/Circ. 1319 dated 11 June 2009. In this case the dimensions relevant to the height and with of the door may be increased of 15% provided that the surface area is not increased of more than 10%.
Reference documents
Naval Suppliers drawings No. FT_PA6ZI_242419_ASM60 Rev. 1 dated 31 January 2019 approved on 6 February 2019 with endorsement No. LABS-1806.
Tests carried out
Test as per RINA Test Laboratory report No. 2019CS01155/2 issued on 6 February 2019 according to IMO 2010 FTP CODE Part 3.




ATTACHMENT TO
CERTIFICATE No. MED049824CS
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****