MED259125CSENGB- -  -  N- SITAL A60 F.R.S.D. -N- S- S- -29/09/2025- Marine Equipment- - SN- S- - N-  - 62,219B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED259125CS- N-Sep 28, 203062219
 
Form
  Marine Equipment(TO)
MED259125CS
Certification N. MED259125CS - (ENG)
Certificate date 29/09/2025
Type Protezione antincendio
Product Porte tagliafuoco
Item Nº MED/3.16
USCG Category N° 164.136

Model or Denomin.
Items
SITAL A60 F.R.S.D.
Applicant SITAL S.R.L.
Place of requester VIA DELL' ARTIGIANATO, 1  %  29028 Ponte Dell'Olio (PC)  % ITALY
Tel. N.,Fax, Email 0523 878421, 0523 875141, alex.bossalini@sital.it
Directive (EU) 2025/1533
Standards IMO MSC.1/Circ.1319,IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.
Reference Documents SOLAS 74 Reg.II-2/9, IMO MSC.1/Circ.1511
Request 16/05/2024
Expire date 28/09/2030
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED259125CS

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2025/1533.
MED Item Nº MED/3.16
USCG Category Nº 164.136
Description Fire doors
Type SITAL A60 F.R.S.D.
Applicant SITAL S.R.L.
VIA DELL' ARTIGIANATO, 1,29028 Ponte Dell'Olio (PC),ITALY
Testing standards IMO MSC.1/Circ.1319,IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.
Reference standards SOLAS 74 Reg.II-2/9, IMO MSC.1/Circ.1511
Issued in Genoa on
This Certificate is valid until
September 29, 2025
September 28, 2030
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED259125CS
Page 1 of 2

Product description

Single-leaf hinged door with a maximum view opening of 1202 mm in width and 2455 mm in height. The leaf, with a width of 1315 mm, height of 2565 mm, and thickness of 75 mm, is made of two carbon steel sheets each 2 mm thick and, inside, the insulating material. The insulation consists of a central layer of material called Pluratect Marine Plus with a nominal thickness of 19 mm and nominal density of 860 kg/m3, and on each side, a layer of alkaline earth silicate fiber called Dalfratherm 1260 ULS Blanket with a nominal thickness of 25 mm and nominal density of 128 kg/m3. The perimeter of the leaf has a rebate composed of the two sheets bent and shaped together.
On the thickness, at the junction between the two sheets that make up the door, there is a stainless steel plate glued with Soudalseal 605 sealant. Inside the leaf, there are shaped “L” stiffeners welded to both sheets, measuring 30x25x2 mm: 4 vertical ones with a variable pitch between 142.2 mm and 660 mm, and 7 horizontal ones with a variable pitch from 80 mm to 860 mm.The leaf is equipped with a window having a view opening of 560x760, made of laminated glass type Climasound fire EI60 with a thickness of 51.5 mm (manufacturer Picco & Martini), provided with glazing bead on each side of the leaf composed of a carbon steel sheet measuring 75 mm, fixed to the leaf by means of M8 stainless steel bolts with a variable pitch between 40 mm and 290 mm. Between the glass and the glazing bead, a Promat gasket type Dalfratherm 1260 ULS paper is provided. The door frame is made of a 4 mm thick carbon steel sheet, properly shaped and measuring 100x84x34 mm, welded end-to-end to the panel sheet. Along the entire perimeter of the frame, on the rebate side, an “L” profile in carbon steel measuring 30x30x2 mm is welded in order to contain the frame insulation. On the side opposite to the hinges, the frame is insulated for a width of 100 mm with two layers of Rockwool SeaRox Sl620 wool with thicknesses of 50 mm and 30 mm, respectively, each having a density of 100 kg/m3, fixed with carbon steel welded anchors. The pins arrangement on the door frame was carried out according to the drawing shown on page 2 of annex number 2 of this test report. The pins are positioned with a pitch of 460 mm. Between the frame and the leaf, an EPDM Assotech gasket type “001.002596” is provided. Along the entire perimeter of the leaf, a Promat heat-expanding gasket type Promaseal-PL-SK/G is provided, measuring 50 mm and 1.8 mm thick. The leaf is equipped with no. 3 hinges type ZCELAX64L and a stainless steel handle type ECO D110. On the side opposite the hinges, the leaf is provided with: a panic bar with three locking points type ECO EPM 900 IV in stainless steel; an ABLOY door closer type DC247 in stainless steel; and a stainless steel door stop hook type ZFPT430DX (or ZFPT430SX).
Field of application
Fire resistant A-60 Class single leaf hinged door. The door is also in compliance with IMO MSC.1/Circ. 1319 dated 11 June 2009. In this case the dimensions relevant to the height and width of the door may be increased of 15% provided that the surface area is not increased of more than 10%.
In case of doors in compliance to the "Agreement between the EEA EFTA States and the United States of America", the present certificate is valid at the following conditions:
- doors without windows or with total window area no more than 645 cm2
- maximum door size tested
- door used with a fire tested frame design
Reference documents
Sital drawing No. "8035-55-5435-ST-DWG-001" Rev. 00 dated 08/08/2025 enclosed on Test Report N.2025CS012591 dated 11/09/2025 .
Tests carried out
Tests as per RINA Test Laboratory Report No. 2025CS012591 dated 11/09/2025 issued according to IMO 2010 FTP Code Part 3.




ATTACHMENT TO
CERTIFICATE No. MED259125CS
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****