MED203423CS!001ENGD- -  -  N- B15 GLAZED TELESCOPIC DOOR - B15DTG2/B15DTG2A -N- S- S- -09/10/2023- Marine Equipment- - SN- S- - N-  - 597,421B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED203423CS/001- N-Oct 8, 2028597421
 
Form
  Marine Equipment(TO)
Certification N. MED203423CS/001 - (ENG)
Certificate date 09/10/2023
Type Protezione antincendio
Product Porte tagliafuoco
Item Nº MED/3.16
USCG Category N° 164.136

Model
Items/Sizes
B15 GLAZED TELESCOPIC DOOR - B15DTG2/B15DTG2A
Applicant BLU BUD SRL
Place of requester VIA CORSICA 21/20  %  16128 Genova (GE)  % ITALY
Tel. N.,Fax, Email 0108601379, 0108183053, info@blubud.it
Directive (EU) 2022/1157
Standard IMO Res. MSC.307(88)-(2010 FTP Code)
Reference Documents Chap. II-2 of 1974 SOLAS Convention as amended, RINA Rules for the certification of Marine Equipment
Request 26/05/2023
Validity 08/10/2028
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED203423CS/001

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2022/1157.
MED Item Nº MED/3.16
USCG Category Nº 164.136
Description Fire doors
Type B15 GLAZED TELESCOPIC DOOR - B15DTG2/B15DTG2A
Applicant BLU BUD SRL
VIA CORSICA 21/20,16128 Genova (GE),ITALY
Testing standards IMO Res. MSC.307(88)-(2010 FTP Code)
Reference standards Chap. II-2 of 1974 SOLAS Convention as amended, RINA Rules for the certification of Marine Equipment
Issued in Genoa on
This Certificate is valid until
October 9, 2023
October 8, 2028
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED203423CS/001
Page 1 of 2

Product description

Triple leaves sliding door with clear light of 1400x2210 mm (WxH). The leaves, having, each, dimensions of 780x2247 mm (WxH) are composed of steel profile FORSTER type FUEGO LIGHT having dimensions of 50x65 mm while the glass compound type PYROBEL 16 EI 30 (manufacturer AGC) having total thickness of 17.3 mm, is composed of three panes and, in between, two layers of thermo-expanding gel. The glass retaining frame, fitted on both side, is composed of hollow stainless steel profiles having dimensions of 20x16.5 mm clipped to the frame. The glass pane is held in place by means of ceramic fiber gaskets having dimensions of 15x5 mm. On the upper side the door is equipped by a steel crossbar having width of 320 mm and thickness of 2 mm, on which are fixed steel guide where slide the suspension trolleys. On the lower side the leaf are equipped by closure dogs CHEMOLLI FIREBOLTS type A2 that acts in a cockpit on the sill. The sill is composed of steel bended profile having width of 320 mm and thickness 1.5 mm and the lock system is mechanical type VC 5382.

Field of application
Fire resistant B-15 Class triple leaves sliding door for general application in compliance with IMO MSC.1/Circ. 1319 dated 11 June 2009. In this case the dimensions relevant to the height and with of the door may be increased of 15% provided that the surface area is not increased of more than 10%.
In case of doors in compliance to the "Agreement between the European Community and the United States of America", the present certificate is valid at the following conditions:
- doors without windows or with total window area no more than 645 cm2 in each door leaf
- maximum door size tested
- door used with a fire tested frame design
Reference documents
BLU BUD drawing No. 23039A900 Rev.2 dated 23 June 2023 enclosed on Test Report No. 2023CS012034 issued on 1th September 2023.
Tests carried out
Test as per RINA Test Laboratory report No. 2023CS012034 issued on 1th September 2023 according to Appendix 1 of IMO 2010 FTPC Part 3.




ATTACHMENT TO
CERTIFICATE No. MED203423CS/001
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****