MED411924CSENGB- -  -  N- DEMON -N- S- S- -28/02/2025- Marine Equipment- - SN- S- - N-  - 433,966B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED411924CS- N-Feb 27, 2030433966
 
Form
  Marine Equipment(TO)
MED411924CS
Certification N. MED411924CS - (ENG)
Certificate date 28/02/2025
Type Protezione antincendio
Product Porte tagliafuoco
Item Nº MED/3.16
USCG Category N° 164.136

Model or Denomin.
Items
DEMON
Applicant METALSTYLE SRL
Place of requester VIA CORSICA 2/17  %  16128 Genova (GE)  % ITALY
Tel. N.,Fax, Email 0185 350345, 00185 1831149, info@metalstyle.com
Directive (EU) 2024/1975
Standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.
Reference Documents SOLAS 74 Reg.II-2/9, IMO MSC.1/Circ.1511
Request 15/02/2025
Expire date 27/02/2030
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED411924CS

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2024/1975.
MED Item Nº MED/3.16
USCG Category Nº 164.136
Description Fire doors
Type DEMON
Applicant METALSTYLE SRL
VIA CORSICA 2/17,16128 Genova (GE),ITALY
Testing standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.
Reference standards SOLAS 74 Reg.II-2/9, IMO MSC.1/Circ.1511
Issued in Genoa on
This Certificate is valid until
February 28, 2025
February 27, 2030
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED411924CS
Page 1 of 3

Product description



Single leaf hinged door whose maximum clear opening size is 800x1800 mm. The leaf, having maximum width of 822 mm, height of 1822 mm and thickness of 126 mm, is composed, on the hinged side, of a stainless-steel plate 4 mm thick and on the not hinged side of a stainless-steel plate 2 mm thick. The joint between the hinged and not hinged stainless steel plates has done by stainless steel screws having diameter 6 mm and pitch 125 mm screwed to a stainless-steel “Z” shaped profile having dimensions of 25x93x24 mm and thick 4 mm welded on the perimeter of the hinged side plate. On the stainless-steel plate thick 4 mm are provided the following stiffeners: 2 vertical stiffeners having a pitch of 248 mm and 3 horizontal stiffeners having a pitch from 580 mm composed of “C” shaped stainless-steel profiles having dimensions of 60x40 mm and thick of 3 mm. Inside the leaf is provided an insulating material compound composed of 1 layer of mineral wool Rockwool type SeaRox SL 660 having density of 150 kg/m3 and thick of 50 mm, 1 layer of non-combustible material type PROMAGUARD 10 mm thick and density of 240 kg/m3 and 1 layer of mineral wool Rockwool type SeaRox SL 660 having density of 150 kg/m3 and thick of 50 mm. The leaf frame is composed of a stainless-steel profile having dimensions of 120 x 80 mm and thick 6 mm fixed to the bulkhead, on the hinged side, by means of a stainless steel counterpale having thickness of 4 mm and width of 76 mm and of No. 108 M10 stainless steel bolts having a pitch of 50 mm. The leaf frame is insulated, on the not hinged side, for its width, with 2 layers of mineral wool Rockwool type SeaRox SL660 having thick 50 mm and density of 150 kg/m3 and 1 layer of PROMAGUARD 10 mm thick and density of 240 kg/m3 fitted by pins and washers. Between the frame and the bulkhead steel plate is provided a layer of seal type Sika Firestop Marine. The leaf closure is made tight with an EPDM gasket Ghirardelli type GH203689 having dimensions of 20x20 mm type fitted in the bended edge on the rabbet which is shielded with a thermo-expanding gasket type Promaseal PL SK thick 1.8 mm fitted on unexposed perimetric door edge and on frame perimetric on the exposed edge to the fire. The leaf is equipped with four hinges and a wedge closing system that acts on 8 steel poles by means of one handle on both sides.

 




ATTACHMENT TO
CERTIFICATE Nr. MED411924CS
Page 2 of 3

Field of application

Fire resistant A-60 Class single leaf hinged door intended for general applications.
In case of doors in compliance to the "Agreement between the European Community and the United States of America", the present certificate is valid at the following conditions:
- maximum door size tested;
- door used with a fire tested frame design.

The surfaces of this division may be fitted with products having low flame spread characteristics, installed as described in the relevant type approval certificates and satisfying the requirements of SOLAS 74 Reg. II-2 as applicable.
Reference documents

Metalstyle drawing No. “Porta stagna DEMON – A60” dated 06/11/2024 reported in the Test as per RINA Fire Protection Laboratory Report No. 2024CS014119/1 issued on 28/02/2025.
Tests carried out

Test as per RINA Fire Protection Laboratory Report No. 2024CS014119/1 issued on 28/02/2025 according to Part 3 Annex 1 of IMO FTP Code 2010 as amended.




ATTACHMENT TO
CERTIFICATE No. MED411924CS
Pages 3 of 3
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****