MED511525CS!046ENGD- -  -  N- B15 CLASS ACOUSTIC DOOR - 2050 -N- S- S- -12/02/2026- Marine Equipment- - SN- S- - N-  - 2,370,495B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED511525CS/046- N-Feb 11, 20312370495
 
Form
  Marine Equipment(TO)
Certification N. MED511525CS/046 - (ENG)
Certificate date 12/02/2026
Type Protezione antincendio
Product Porte tagliafuoco
Item Nº MED/3.16
USCG Category N° 164.136

Model or Denomin.
Items
B15 CLASS ACOUSTIC DOOR - 2050
Applicant MARINE INTERIORS S.P.A.
Place of requester VIA GENOVA 1  %  34121 Trieste (TS)  % ITALY
Tel. N.,Fax, Email ---, ---, marco.varriale@fincantieri.it
Directive (EU) 2025/1533
Standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.,IMO MSC.1/Circ. 1319
Reference Documents IMO MSC.1/Circ. 1511/Rev.1,SOLAS 74 Reg. II-2/9
Request 3/8/2021
Expire date 11/02/2031
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED511525CS/046

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2025/1533.
MED Item Nº MED/3.16
USCG Category Nº 164.136
Description Fire doors
Type B15 CLASS ACOUSTIC DOOR - 2050
Applicant MARINE INTERIORS S.P.A.
VIA GENOVA 1,34121 Trieste (TS),ITALY
Testing standards IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.,IMO MSC.1/Circ. 1319
Reference standards IMO MSC.1/Circ. 1511/Rev.1; SOLAS 74 Reg. II-2/9
Issued in Genoa on
This Certificate is valid until
February 12, 2026
February 11, 2031
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED511525CS/046
Page 1 of 2

Product description

Single leaf hinged door whose maximum clear opening size is 1000x2050 (WxH) mm. The door leaf, having maximum dimensions of 1033x2061 (WxH) mm, is composed of two steel sheets, 0.8 mm thick each and, in between, the insulating material. This insulation is composed, on each side, of a layer of mineral wool (certified non combustible in conformity to the requirements of the IMO FTP Code) type PAROC MARINE SLAB 220 having thickness of 15 mm and density of 220 kg/m3 and an internal layer of mineral wool type PAROC MARINE SLAB 130, 20 mm thick and having density of 130 kg/m3. The insulating materials are glued to the steel sheets by means of 70 g/m2 of adhesive type SikaForce-7110. The leaf is fitted, on the perimeter, with C shaped steel profiles having dimensions of 55x13.5 mm and thickness of 0.8 mm. The door frame is composed of hollow steel profiles, 1.2 mm thick fixed to the bulkhead by means of screws 4.2x13 mm. Between leaf and frame gaskets type Marine Interiors silicone 50, are fitted. The door may be equipped with a an automatic threshold type “Comaglio PRESSURE 1770”.

Field of application
Fire resistant B-15 Class door.
In case of doors in compliance to the "Agreement between the European Community and the United States of America", the present certificate is valid at the following conditions:
- doors without windows
- maximum door size tested
- door used with a fire tested frame design

Reference documents
Marine Interiors Cabins SpA drawings:
  • No. 24PC00366 enclosed to CSI Test Reports No. 0060/DC/RFM/21.
  • No. 24PC00367 Rev. 1 dated 13 October 2021 approved on 15 October 2021 with endorsement No. LABS-2274

Tests carried out
Tests as per CSI Test Laboratory report No. 0060/DC/RFM/21 issued on 18 October 2021 according to IMO 2010 FTP Code Part 3.




ATTACHMENT TO
CERTIFICATE No. MED511525CS/046
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****