MED461525CSENG- -  -  N- SITAL A60 F.R.D.D. -N- S- S- -14/01/2026- Marine Equipment- - SN- S- - N-  - 62,219B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED461525CS- N-Jan 13, 203162219
 
Form
  Marine Equipment(TO)
Certification N. MED461525CS - (ENG)
Certificate date 14/01/2026
Type Protezione antincendio
Product Porte tagliafuoco
Item Nº MED/3.16
USCG Category N° 164.136

Model or Denomin.
Items
SITAL A60 F.R.D.D.
Applicant SITAL S.R.L.
Place of requester VIA DELL' ARTIGIANATO, 1  %  29028 Ponte Dell'Olio (PC)  % ITALY
Tel. N.,Fax, Email 0523 878421, 0523 875141, alex.bossalini@sital.it
Directive (EU) 2025/1533
Standards IMO MSC.1/Circ.1319,IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.
Reference Documents SOLAS 74 Reg.II-2/9, IMO MSC.1/Circ.1511/Rev.1
Request 10/10/2025
Expire date 13/01/2031
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Enrico Cabella S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED461525CS

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2025/1533.
MED Item Nº MED/3.16
USCG Category Nº 164.136
Description Fire doors
Type SITAL A60 F.R.D.D.
Applicant SITAL S.R.L.
VIA DELL' ARTIGIANATO, 1,29028 Ponte Dell'Olio (PC),ITALY
Testing standards IMO MSC.1/Circ.1319,IMO Res. MSC.307(88)-(2010 FTP  Code), as amended.
Reference standards SOLAS 74 Reg.II-2/9, IMO MSC.1/Circ.1511/Rev.1
Issued in Genoa on
This Certificate is valid until
January 14, 2026
January 13, 2031
This Certificate consists of this sheet plus an attachment

________________________________________
Enrico Cabella
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED461525CS
Page 1 of 2

Product description

Double-leaf hinged door with a clear view of 2458 mm in width and 2455 mm in height.
The primary leaf, with a width of 1246 mm, height of 2565 mm, and thickness of 75 mm, is made of two 2 mm thick carbon steel sheets and, internally, insulating material.

The insulation consists of a layer of alkaline earth silicate fiber called Dalfratherm 1260 ULS Blanket with a nominal thickness of 25 mm and a nominal density of 128 kg/m³, and, on each side, a layer of material called Pluratect Marine Plus with a nominal thickness of 19 mm and a nominal density of 860 kg/m³.
The perimeter of the primary leaf features a rebate formed by the two sheets bent and shaped together. Within the thickness, at the joint between the two sheets forming the door, there is a stainless-steel flat bar bonded with Soudalseal 605 sealant. Inside the primary leaf, L-shaped stiffeners are provided, welded to both sheets, with dimensions 30×25×2 mm: 4 vertical stiffeners with variable pitch between 142.5 mm and 660 mm, and 7 horizontal stiffeners with variable pitch from 80 mm to 860 mm.
The primary leaf is fitted with a window with a clear opening of 560×760 mm, made of laminated glass Climasound fire EI60, 51.5 mm thick (manufacturer Picco & Martini), provided with glazing beads on each side of the leaf, consisting of a 75 mm wide carbon steel sheet, fixed to the leaf by stainless-steel M8 bolts with variable pitch between 40 mm and 290 mm. Between the glass and the glazing bead, a Promat Dalfratherm 1260 ULS paper gasket with dimensions 20×2 mm is provided. The secondary leaf, with a width of 1243 mm, height of 2565 mm, and thickness of 75 mm, is constructed identically to the primary leaf.
The door frame is made of 4 mm thick carbon steel sheet, suitably shaped, with dimensions 100×84×34 mm, butt-welded to the bulkhead plate. Around the entire perimeter of the frame, on the rebate side, an L-shaped carbon steel profile with dimensions 30×30×2 mm is welded, in order to contain the frame insulation.
On the side opposite the hinges, the frame is insulated over a width of 100 mm with two layers of Rockwool SeaRox Sl620 mineral wool with thickness of 50 mm and 30 mm respectively, each having a density of 100 kg/m³, fixed with welded carbon steel pins. The arrangement of the pins on the door frame has been carried out according to the drawing included in the relevant test report. The pins are positioned at a pitch of 460 mm.
Between the frame and the leaves, an Assotech EPDM gasket type “001.002596” is provided. Around the entire perimeter of the leaves, an intumescent gasket Promat Promaseal-PL-SK/G is provided, with a width of 50 mm and a thickness of 1.8 mm.
Each leaf is equipped with three stainless-steel ZCELAX64L hinges. The primary leaf is fitted with a stainless-steel handle type ECO D110, while on the side opposite the hinges it is provided with a three-point panic exit device ECO EPM 900 IV in stainless steel and an ABLOY DC247 stainless-steel door closer.
On the secondary leaf, a stainless-steel locking rod Fuzhou Conssin ZKITIXAST27 + ZCELAX27L is provided. Both leaves are equipped with a door hold-open hook type ZFPT430DX (or ZFPT430SX) made of stainless steel.
Field of application
Fire resistant A-60 Class double leaf hinged door. The door is also in compliance with IMO MSC.1/Circ. 1319 dated 11 June 2009. In this case the dimensions relevant to the height and width of the door may be increased of 15% provided that the surface area is not increased of more than 10%.
In case of doors in compliance to the "Agreement between the EEA EFTA States and the United States of America", the present certificate is valid at the following conditions:
- doors without windows or with total window area no more than 645 cm2 in each door leaf.
- maximum door size tested;
- door used with a fire tested frame design.
Reference documents
Sital drawing No. "8036-55-5465-ST-DWG-001" Rev. 00 dated 13/10/2025 enclosed on Test Report N.2025CS014615 dated 14/01/2026 .
Tests carried out
Tests as per RINA Test Laboratory Report No. 2025CS014615 dated 14/01/2026 issued according to IMO 2010 FTP Code Part 3.




ATTACHMENT TO
CERTIFICATE No. MED461525CS
Pages 2 of 2
The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
XXXX/YY
"WHEELMARK FORMAT"

XXXX
Notified Body number undertaking surveillance module
YY
Last two digits of year mark affixed
     
______________________________________________
General conditions for the approval
a) The initial conditions verified by RINA at the time of the approval are to be maintained
b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


__________________________________________
Enrico Cabella
**** NOTICE: This is NOT an official certificate ****