MED293926CSENGD- -  -  N- AQUATECH WM 101 -N- S- S- -25/06/2026- Marine Equipment- - SN- S- - N-  - 137,283B2bisMarine EquipmentNumero Pratica,Direttiva,Norma,Schema,Richiesta,Validità,EmailR- MED293926CS- N-Jun 24, 2031137283
 
Form
  Marine Equipment(TO)
Certification N. MED293926CS - (ENG)
Certificate date 25/06/2026
Type Protezione antincendio
Product Fixed water based local application fire fighting systems components for use in category "A" machinery spaces (Nozzles and performance tests)
Item Nº MED/3.48

Model or Denomin.
Items
AQUATECH WM 101
Applicant TEMA SISTEMI SPA
Place of requester VIA ROMAGNOLI N. 4  %  48026 RUSSI (RA)  % ITALY
Tel. N.,Fax, Email 0544471350, 0544471350, ufficio.qualita@temagroup.eu
Directive (EU) 2025/1533
Standards IMO MSC/Circ. 1387
Reference Documents Reg II-2/10, IMO Res.MSC 36(63), IMO Res.MSC 97(73)
Request 10/02/2026
Expire date 24/06/2031
EC TYPE-EXAMINATION (MODULE B) ENG
Vuoto Querysave
Davide Campora S

EC TYPE EXAMINATION (MODULE B)
CERTIFICATE No. MED293926CS

This is to certify that RINA Services S.p.A. (Notified Body No. 0474) did undertake the relevant type approval procedures for the equipment identified below, which was found to be in compliance with the Fire Protection requirements of Marine Equipment Directive (MED) 2014/90/EU, including the requirements and testing standards of Regulation (EU) 2025/1533.
MED Item Nº MED/3.48
Description Fixed water based local application fire fighting systems components for use in category "A" machinery spaces (Nozzles and performance tests)
Type AQUATECH WM 101
Applicant TEMA SISTEMI SPA
VIA ROMAGNOLI N. 4,48026 RUSSI (RA),ITALY
Testing standards IMO MSC/Circ. 1387
Reference standards Reg II-2/10, IMO Res.MSC 36(63), IMO Res.MSC 97(73)
Issued in Genoa on
This Certificate is valid until
June 25, 2026
June 24, 2031
This Certificate consists of this sheet plus an attachment

________________________________________
Fabio Morbioni
RINA Services S.p.A.
**** NOTICE: This is NOT an official certificate ****

ATTACHMENT TO
CERTIFICATE No.  MED293926CS
Page 1 of 2
Materials/Components

Pumps, piping, tanks, valves, section valves, open nozzles, filters, control and monitoring systems as described in Tema Sistemi Technical Documentation Booklet.
The open type Bronze (Cu Sn 12) nozzle designated as WM 101 is represented in the relevant drawing. The nozzle is also available in nickel coated version.
Fields of application

Local application fire-fighting system for the protection of high fire risk areas in machinery spaces of category A as required by Reg. II-2/10.5.6.2 of SOLAS 74, as amended. The system may also be arranged on high speed crafts in compliance with para. 7.7.3.2 chapter 7 of HSC Code as amended by resolution MSC.97(73).

Nozzles type AQUATECH WM 101 arrangement and main characteristics
K-factor (lpm/bar1/2)
1.0
Nominal operating pressure
100 bar (nominal); 90-110 bar (min-max)
Minimum vertical distance to fire source
2 m
Maximum vertical distance to fire source
10 m
Maximum nozzle spacing
4 m
Nozzle arrangement (*)
3x3 (square arrangement)

(*) According to Par 3.4.2.2 of Appendix to MSC.1/Circ.1387.
The outer nozzles can be located either at the edge of the protected area or outside of the protected area.
Single row installation: the outer nozzle should be placed at least at the edge of the protected area with max horizontal spacing of 2 m.
Reference documents
  • Tema Sistemi Technical Documentation Booklet and Enclosures filed by RINA with n. CSST-7039, CSST-7040 and CSST-7041 and CSST-7045.
  • Tema Sistemi WM 101 nozzle drawing approved by RINA with n. CSST-26432.
  • TESI Laboratory test report n. 188/C dated 30/06/2010, filed by RINA with n. CSST-7037.
  • Tema Sistemi Test Report n. TS/WM101/02/07 dated 28/06/2010, filed by RINA with n. CSST-7035.
  • Test Report n° TS/WM/01/21 issued by Brand technology filed with n° CSST-19035.




  • ATTACHMENT TO
    CERTIFICATE No. MED293926CS
    Pages 2 of 2
    The mark of conformity may only be affixed to the above type approved equipment and a Manufacturer's Declaration of Conformity issued when the production control phase module (D, E or F) of Annex II of the Directive is fully complied with a written inspection agreement with a Notified Body
    XXXX/YY
    "WHEELMARK FORMAT"

    XXXX
    Notified Body number undertaking surveillance module
    YY
    Last two digits of year mark affixed
         
    ______________________________________________
    General conditions for the approval
    a) The initial conditions verified by RINA at the time of the approval are to be maintained
    b) Any changes to the initial conditions are to be promptly communicated to RINA, which reserves the right to repeat the relevant assessment
    c) This certificate will no be valid if the manufacturer makes any changes or modifications to the approved equipment, which have not been notified to, and agreed with RINA
    d) RINA personnel are to be allowed to witness during the performances of activities, upon their request
    e) The activities are to be carried out in compliance with the RINA Rules and/or other applicable Rules

    f) Should the specified regulations or standards be amended during the validity of this certificate, the product is to be reapproved prior to it being placed on board vessels to which the amended regulations or standards apply. 


    __________________________________________
    Fabio Morbioni
    **** NOTICE: This is NOT an official certificate ****